Jump to content
SAU Community

Recommended Posts

Hello,

I think this might be my first post but any way i have problems :D

The car taking ages to turn over when cold and not as long when hot. When its cold it takes many pumps of the pedal and 2 or 3 turns of the key as to not kill the starter.

When the car is hot its the similar but doesnt need as much pushing of the pedal to fire.

I changed the spark plugs thinking that it might be them....but no

Changed the fuel filter....but no.

Tried taking air-filter off to start car....but no.

The car doesnt feel down on power so not the fuel pump? it's only a starting issue.

Don't know what else i can try? so im looking for suggestions.

The car does have a Mines ECU (which i was stoked to find) but it hadnt effected the starting before. Also has a 3 inch off the dump pipe, CAT and a choking blitz muffler on the back. Other than that, it's stock.

It's been a couple of weeks like this now.

Im after any ideas any of you might have.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/198298-2000-stagea-s-tune-starting-issue/
Share on other sites

cold days/nights my car is the same, doesnt fire, plugs are fine etc, everything has been serviced, hot days its fine. New pump will go in soon and will be checking fault codes when the informeter arrives... let me know how you go. I didn't gap my plugs down, could that be it?

Now winter is over i have no probs :D

Edited by Ryan1600

when i first got my car i had heaps of problems getting her to start to the point it would take you 5 or 6 pushes on the pedal while you were trying to start it to actually get it going.... my problem was the fact the compliancer had run her out of petrol...2 or 3 weeks later when i had good fuel in her she was fine...now 12months down the track still no problems at all *crosses fingers*

when i first got my car i had heaps of problems getting her to start to the point it would take you 5 or 6 pushes on the pedal while you were trying to start it to actually get it going.... my problem was the fact the compliancer had run her out of petrol...2 or 3 weeks later when i had good fuel in her she was fine...now 12months down the track still no problems at all *crosses fingers*

I keep mine over half a tank with 98 or 100RON

You shouldn't be pumping the pedal on ANY fuel-injected car when you're starting it - it's all controlled electronically, so there's no need for you to try and add more fuel to get it started. This might be part of the problem.

Also, have you checked the small in-line fuel filter near the tank? That often gets clogged first as it's the nearest filter to the tank, so have a look to see if there's anything blocking it.

Oh, and like Kirstie, I never let my fuel level drop below a quarter tank - when the level gets that low there's more of a chance that it the pump will pick up all of the crap that sits on the bottom of the tank, and then your filters will get clogged more quickly.

You shouldn't be pumping the pedal on ANY fuel-injected car when you're starting it - it's all controlled electronically, so there's no need for you to try and add more fuel to get it started. This might be part of the problem.

Also, have you checked the small in-line fuel filter near the tank? That often gets clogged first as it's the nearest filter to the tank, so have a look to see if there's anything blocking it.

Oh, and like Kirstie, I never let my fuel level drop below a quarter tank - when the level gets that low there's more of a chance that it the pump will pick up all of the crap that sits on the bottom of the tank, and then your filters will get clogged more quickly.

on a cold day, pumping is the only way to start it, could be TPS? Also primed the pump a few times before starting, doesn't make a difference

pumping the pedal - yeah.. not a good idea on an EFI car. the only time you should be screwing with the accelerator on startup is if you think the car is " flooded" with fuel .

opening the throttle body butterfly valve will allow more air inside and hopefully get rid of some of the excess fuel vapours and also allow a bit more air in there so that the mixture will eventually fire.

have you tried changing the heat range of your plugs? ie go hotter or colder?

what do the plug tips look like when you take them out .. can you show us a pic?

can you hear the fuel pump prime?

is the edge of the butterfly valve in the throttle body clean? or is it gunked up?

from what I understand ( least on sr20's / my RB knowledge is still on a learning curve) there is a small pin hole that lets a bit of air past hte butterfly valve on idle - and maybe check your idle air control valve? they sometimes get gunked up and need a clean

where exactly is that filter?

Some EFI cars have them, not all - haven't checked the Stagea, so I don't know if there is one there or not. It's usually in the line just after where the fuel lines come out of the tank. My old man's Camry (from way back when) had one that got clogged on the way down to Melbourne one year which had him scratching his head for quite a while until it was pointed out by someone else.

I've seen it on a few cars, but I couldn't confirm if the Stagea has one or not as I've never checked for it.

or if you dont want to get the fuel injectors cleaner you can pump United fuel Boost 98 which is able to clean the lines cos of the ethanol added into it. Im using boost 98 most of the time. If i have the coupond fuel vouchers i will use it.

pumping the pedal - yeah.. not a good idea on an EFI car. the only time you should be screwing with the accelerator on startup is if you think the car is " flooded" with fuel .

opening the throttle body butterfly valve will allow more air inside and hopefully get rid of some of the excess fuel vapours and also allow a bit more air in there so that the mixture will eventually fire.

have you tried changing the heat range of your plugs? ie go hotter or colder?

what do the plug tips look like when you take them out .. can you show us a pic?

can you hear the fuel pump prime?

can hear it prime, then stop, turn acc off, then back on to reprime... When i pull everything apart to clean it, any directions as to what i am cleaning, what to use to clean it, and can i stuff any adjustments whilst doing it?

-Ryan :D

Fuel pump switches off once there is pressure in the system and the engine is not running so no need to keep pumping to maintain pressure. Switching it on and off multiple times won't make any difference, the fuel system is either pressurised, or not... Happening when it's cold suggests it might be a sensor playing up... Check error codes would be a good start.

well I dont know for sure..( as I have only cleaned the IAC valve on the pulsar ) but I would assume the same thing applies to the RB motors.

what do the sparkplugs look like? is the colour ok ?

can hear it prime, then stop, turn acc off, then back on to reprime... When i pull everything apart to clean it, any directions as to what i am cleaning, what to use to clean it, and can i stuff any adjustments whilst doing it?

-Ryan :D

Update....

I know you're not supposed to pump the pedal, but if i didnt it would probly just crank all day and not fire. Sometimes it will start first go but rarely.

It feels like its starting to lose some down low power, but is almost as fast at hight revs 4500+

Can't hear fuel pump prime, ive never been able to hear a stock fuel pump prime in any car.

Is it possible the fuel pump could be dying? A mates sprinter would start but stall past 3000rpm = stuffed fuel pump. Another mates silvia would lose power at 5000rpm and stall pretty much = stuffed fuel pump again.

But mine not getting fuel at start up = stuffed fuel pump?!?

A dirty/rooted O2 sensor do it?

The plugs that i took out of the car, the tips were white possibly too hot?. not fouled and black.

I might check out the throttle body tomorrow, when i did the plugs there was some black shite (oil/dirt) on the cooler piping inner walls. I just assumed it was a crud build up.

Thanks for your suggestions. :P

Edited by Whooby
  • 3 weeks later...

Update:

Tried a larger fuel pump, good for up to 500HP - No change, bit too much fuel for a stock engine.

Could it be a crank angle sensor perhaps? once the engine fires there is a Tick Tick Tick then stops. Not sure what it is yet.

Any help please :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...