Jump to content
SAU Community

Recommended Posts

Hey There,

Got my new engine put in this week, and after a bit of driving around etc i've noticed that sometimes when the revs are low and building up to boost

at about 2500rpm the car stutters a bit and feels like its holding back, then once it gets past there it boogies.

Now, i had a major issue with one of the cams f**king up so one of my old cams was used in the motor as the other was broken, now if the cams were say to be different would this cause the issue? The cams supposably on the new engine were NA ones but im unsure of this as a fact.

The car doesnt really pull hard on 14psi as it used to, it used to throw you back in your seat now the car just seems to pull along the revs?

Also thinking Injectors or fuel pump?

Help! I wanna get this fixed!

Trent

oh ok sorry - so the engine was just put back in the car?

id say something is loose, like a hose clamp, intercooler pipe work, the air vac lines for the actuator etc - something along those lines?

Well its not the gap on the plugs

After a fair bit of reading ive come to the conclusion that its the fuel pump not sending enough to the engine, probably causing it to lean out. The car runs fine when cold but thats when its running rich but as soon as it settles its stuffed.

"Many of you with S13s have probably experienced hesitation on boost which can start to happen when the standard fuel pump is getting old."

I believe thats what my problem is.

Now im estimating that its dangerous to drive the car whilst in this state, i.e fuel pump could break down, or could lean the engine out.

Would i be right saying that?

it will be dangerous for you to give the motor any reason to demand more fuel yes.. like cracked piston spec. putting around not so much the best thing for you to do man is take it to a dyno and get your air/fuel checked out they will be able to tell u if it is leaning out or not, if so extreemly likely tis the fuel pump

what gap and how much boost are you running? I was running 14 psi and I had a stutter even after I put in a new 040 pump and pulled the gap from 1.1 to .8 and it stopped it

Edited by BANGN
  • 2 weeks later...

Car was datalogged today, we found that the timing was out. We also adjusted the teeth so that it was sitting perfectly.

We also changed over to a working CAS which still didnt fix the problem, the timing was jumping around from sitting on 15 to 7/8 up and down. Also tried a few diff coilpacks but we are unsure if they are working correctly.

I'm waiting on my walbro replacement to come back then ill be installing that into the tank see if that fixes the issue, other than that its coil packs/injectors we are thinking.

Anyone able to add some to the situation?

Also, if somone could be nice enuff who lives in the melbournes west to let me borrow there coilpacks for 2 minutes to see if the car runs any better would be appreciated.

For a 180sx SR20 Red Top

Anyone who can help either post or pm me please!

My car does the same sometimes, most likely cause would be either fuel pump or injectors. i have a power fc and when it happens i look at the inj duty and its 100% . It never used to it when i had 550cc in there. Two ways to fix it....

1. Bigger fuel pump, Fuel reg and bigger Injectors and tune.. or

2. Turn the boost down.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...