Jump to content
SAU Community

Recommended Posts

hey everyone ive jsut had an accident which was my fault in a parking lot. now her damage isnt bad at all it just has some scratches on the right side on the rear. but my cars front is rather wrecked i have a huge dent on the bonnet and the bonnet is lifted up now on one side also my headlights on the left side are pushed in and some little scratches. ok the lady said she will get a quote and get back to me if it isnt that much should i just pay it or call up my insurance company. i think my car might need a new bonnet now does anyone know where i can get one and fast because i want my car ready for the next cruise because it will be my first. any advice would be greatly appreciated.

thanks.

Check parts in the for sales area of the forums.

Get some quotes done for yourself, I recommend Imperial Finish Body Works on centre road in springvale, did a mint job on mine and my mates lines'.

If possible, avoid making a claim on your insurance, if youre a young male your excess is probably huge and your premium will go up of course.

well given what youve said your cars damage is gonna be a few $k easily

if you have full comp then pay the excess and both cars get fixed no mess no fuss

if you only have 3rd party then its probably still worth making a claim to get her car sorted

thanks guys for the responses. i do have full comp im just awaiting to see how much hers will cost because her car looks ok i dont think it should cost to much but mine looks like they would probably replace the bonnet and maybe the front bumper as well which really sucks. maybe this is an excuse to get a gtr front end conversion :( .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...