Jump to content
SAU Community

Recommended Posts

Evening fellow car lovers...

My car - R33 GTST

Recently i did the following modifications... upgraded to R34 GTT intercooler, installed Turbo Smart Dual Stage Boost Controller (switch mounted in cabin to switch between a high and low boost setting) and a Drift Boost Guage. Installed everything myself...

Now... with the boost controller at its minimal settings (as low as the dials can go), im getting 2 different boost readings between the factory guage and the aftermarket one. I installed the aftermarket one onto the thicker hose commin off the intake manifold goin to the fuel pressure regulator (so the guages are taking readins of opposite sides of the intake manifold).

Stock guage is telling me about 8-9 psi... aftermarket guage is telling me 0.75 bar... thats like near 11psi??

Why/Which is correct??? :down: lol in oversight whats the point of having a dual stage boost controller if at its low boost setting its already at the limit of the factory turbo :D (i wasnt planin on upgradin the turbo)

Any input would be greatly appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/199271-different-boost-readings/
Share on other sites

Firstly, a gauge is only as good as the manufacturer. It's not beyond the realms of possibility for 2 different gauges to give 2 different readings of the same thing. The Nissan factory gauges are notoriously inaccurate, though.

And a boost controller cannot lower the boost below standard. It can only raise boost above standard.

Firstly, a gauge is only as good as the manufacturer. It's not beyond the realms of possibility for 2 different gauges to give 2 different readings of the same thing. The Nissan factory gauges are notoriously inaccurate, though.

And a boost controller cannot lower the boost below standard. It can only raise boost above standard.

Like the man says, if you are concerned get your aftermarket boost gauge calibrated.

Cheers GW

The aftermarket boost controller, should be able to get boost BELOW 7PSi, if installed correctly.

The factory actuator is only a 3PSi setup.

The question is, did you remove the factory solenoid?

Also, have you removed the ball and spring from the Turbo Smart tee-piece?

Those boost controllers aren't that great... I ran one, switched for the little $20 boost controller and haven't looked back!

The aftermarket boost controller, should be able to get boost BELOW 7PSi, if installed correctly.

The factory actuator is only a 3PSi setup.

The question is, did you remove the factory solenoid?

Also, have you removed the ball and spring from the Turbo Smart tee-piece?

Those boost controllers aren't that great... I ran one, switched for the little $20 boost controller and haven't looked back!

Uhhh no Im pretty sure the stock R33 GTST actuator is set at 7psi...

Have you ever actually seen a 33 hold 3psi on a stock turbo with everything functioning correctly?

I did remove the factory boost solenoid... and what spring inside tpeice???? lol i just hooked the tpeice between the turbo nd wastegate like the instructions said and blocked off the other top hose which went to the factory boost solenoid... nd yeah at its minimal settings its at like .75 bar lol

What sort of things would i need to check to see if anythin went wrong in installation?? Im pretty sure i did everything correctly though cause it all works lol

Uhhh no Im pretty sure the stock R33 GTST actuator is set at 7psi...

Have you ever actually seen a 33 hold 3psi on a stock turbo with everything functioning correctly?

Yeah the stock actuator is two stage. 5psi to 5000rpm then 7psi to redline :thumbsup:

I take it that your Drift boost gauge just a cheap knock off, in which case its properly as useless as the stock one. Go out and get a proper brand gauge, personally i wouldnt use any thing less than autometer (not autogague) so that means around the 100-150mark depending where you get it from, if you want to spend more on apexi and the like thats all good, you'll probably get an even more accurate reading but in your case an autometer should serve you well.

If you have the basic breathing mods done, ie fmic, turboback exhaust and filter than on low boost with no solinod you should be around the 6-7psi mark.

The location on the manifold where you get your vacuum/boost reading doesnt matter as long as its definately a manifold feed.

LOL, where do you go about getting boost guages caliibrated?

Nearly missed this, first off gauge needs to be cabable of being opened without terminal damage being inflicted. (best option) if not can get correction chart? The yellow pages is always a good place to start, mechanical gauge range = press - 0 - vacuum, electrical = take sensor also. Any NATA instro calibration company or connections to airforce/airlines/altimeter calibration joints, know anyone in the sky-diving game.......breathing? :thumbsup:

Cheers GW

Heya, i dont think the drift guage is faulty, it sells for 90 bux... nd is pretty lol...

I havent done air intake or exhaust mods yet... pod filter is on its way from ebay :banana: nd exhuast wont be for a while. Ahwell i dont really need the turbo to boost more than it is at the moment anyway lol, after i get the exhaust and a safc ill get tuned on a dyno and they can look at it then :down:

thanx for input guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • f**kin' yikes! That insulation is the shittest stuff I have ever seen. You need to do an insurance job on that f**ker, pronto. WRT to the washer cover, I would have said that there'd have to be some at a wrecker, then remembered that it's a BMW, and reasoned that every single wrecked one would have been tailgating and so the front end would be trashed.
    • Oh and I lost my headlight washer jet cover!
    • Ok, so I got myself some X1 wheels really cheap to try out, they're a bit different and I like them but they're really narrow (18x8) they are available in staggered 18x8/9 also but really hard to find.  I kinda dig them, but not as much as the F10 19's I usually run, so these go into the wheel pile.         As I mentioned in another thread, I got a new exhaust. It's an off-the-shelf stainless one that fits OH-KAY. I don't love the tips size and how far they come out the back, I think I might cut the tips off and replace with some smaller (~3") ones that don't extend as far. It sounds really good though, I'm not sure if its just in my head but the car feels a little quicker, more responsive.      I fitted an eBay special front lip. Surprisingly it fit perfectly and all holes lined up. Its a little rickety but I haven't put any double sided tape on yet, I want to clean the front bar up where it has scraped the road a lot and fil in the number plate holes (or, get body coloured wrap to cover them - is this a thing?  I'm not sure if I'll leave it gloss or pain it matte. I really like it though, I don't particularly like the front bar without it, I don't really like the M-Sport and to get anything else is just too expensive. That said, I might need a new one now anyway as I dropped the car onto the jack after forgetting to put ramps under the front wheels. It bent a lot and while it did go back to normal after I got the car off the jack, I do fear I have not done it any favours.    Lastly, my headlights died. Different problems in each. They have gotten much dimmer over the past year or so, I put new (uber expensive) OSRAM bulbs in them but to no avail. One of them pointed at the ground and the other just kinda did its own thing with light working sometimes. Yeah, check this 18 year old BMW headlight wire. I reckon I know why they were stuffed.            BTW, the yellow and black is the power to the Xenons. Yikes. I hunted around an researched my options here. I would have loved to just get a replacement harness but not a thing. My car has adaptive headlights, that is they rotate left and right with the steering wheel. Good condition used adaptive xenons were over $700 each, non adaptive were around $400 each, but I couldn't help but think that they're all around 18 years old now, surely they'd have the same problems. So I looked at newer LCI headlights but they were even more expensive and I couldn't confirm that they'd be plug and play with lots of people having lots of opinions so not worth the risk.  I ended up getting brand new Chinese headlights from MARS. They're very close to OEM with only the angel eyes being a bit different. I didnt want crazy turn signals or sharp DRL's or anything. Not my bag.  They're not adaptive, I thought thats a feature I wouldn't really miss. So I coded that out.  The lights are awesome, they look so nice and they take so many years off the car. The angel eyes look great and the headlight brightness is ridiculous. I was so used to the old ones, I didn't realise just how bad they were. The new ones use the OEM bulbs, Xenon ballast and leveller motor which I was happier with. The only issue with them is that the rear cover is held on by SEVEN screws. This will be a nightmare to get to and open when I need to change bulbs.   
    • Now that you mention it I can see those too. More subtle. The lighting and low resolution makes it hard to assess super well what's going on but what is visible is bad enough to pull the motor.
    • I feel like this is due an update
×
×
  • Create New...