Jump to content
SAU Community

Fibreglass Repair

lingeringsoul

By lingeringsoul,
in General Automotive Discussion

 Share

Recommended Posts

lingeringsoul Grand Master

lingeringsoul

Posted
Posted

Just after some advise from the general public on how fibreglass repair kits work. I cracked my front bar on track a week ago and I've decided to repair it.

The kit has fibreglass sheet, a tin of catalyse and tube of hardener..........and a brush.

I would assume you cut the sheet to appropriate size, mix hardener with catalyst and brush on to the damaged area and let it harden?

Link to comment
https://www.sau.com.au/forums/topic/199347-fibreglass-repair/
Share on other sites
VB- Veteran

VB-

Posted
Posted

yeh mix catalyst and resin, put the sheet over the area and dab the resin on with a brush, dont use strokes, dab it on. i cant remember why or even if im right lol. maybe someone should clarify?

depending on how bad it is, you might be better off putting it along the back or the damaged area, then when its all solid, bog up the front, sand it back and paint it pretty again :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Sounds like it is rotational in the driveline. CV? Tailshaft CB? Also.....didn't you just pay to have that bit painted and put on the car?
    • GTSBoy
      R34 GTT idle problem

      By GTSBoy · Posted

      Yeah, when I dialled my idle down, given how much time I spent idling at the lights in traffic on my daily commute, the effect on overall fuel consumption was absolutely noticeable.
    • Dose Pipe Sutututu
      R34 GTT idle problem

      By Dose Pipe Sutututu · Posted

      Emissions, fuel consumption, heat, noise, etc. most likely.
    • joshuaho96
      R34 GTT idle problem

      By joshuaho96 · Posted

      For me at least the reason why it bothers me is because it's indicative of a deeper problem. And that will nag at me forever. Especially because I have tailpipe emissions testing + evap leak testing every 2 years.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      WELP. I went to the track, and I suppose it went okay because any time you can drive home is okay. You may notice the car is not on the circuit in this picture. It was about 35C day out in Benalla which means the track was approximately the surface of the sun, probably. Good things, car did not overheat but it _was_ warmer than when I had done track days in similar heat before, I think, I'm not sure - I can't quite remember. Coolant got to ~105 via the ECU after 20-30 minutes of belting it in said heat. Oil got up to 145C in one instance which is pretty crazy due to oil cooler. Pressures were fine. I seem to remember this not getting quite so high before the vents. More HMMMM'ing to be done. On the subject of HMMM'ing, can anyone identify the sounds in the video below, you will know which ones I mean: https://www.youtube.com/watch?v=uj3BkI2cbTc I included some 'normal' sound as a reference for the first minute or so. The microphone in this instance was where the license plate is. It stopped working later in the day which is why my "best example of a lap video (not produced)" had internal audio - Isn't hearable from inside the car. I don't mean the chirping of the un-bedded/badly bedded track brakes which you can only hear while braking... Thoughts, brains trust?
×
×
  • Create New...