Jump to content
SAU Community

Recommended Posts

Some small facts first off - r33 gtst s2 (1996) with no mods apart from apexi pod.

I recorded a video using my mobile phone so the quality isnt the greatest. Ill try to provide an explaination to help.

http://www.youtube.com/watch?v=02Cyv2CWqDU

In the video you can see that my idle is fluctuating from about 100-1000rpm. This occurs when ive been driving the car for around 5-10 minutes, or generally once its all warmed up properly. You may also notice that as the rpm fluctuates, so does the vac/boost.

About 3/4 through the video you can see me open the throttle a little bit. The following is what i deal with on the roads when driving. Say im in second and approaching a corner or roundabout and have to give way so i slow down. Its very likely that the car will completely drop off all rpm and die on me. In the video im in neutral or first with the clutch in i forget. Either way, when im in first and i start to slow down a bit after opening the thottle, its very likely that the rpm will drop off to around 0 but not actually stall completely. As seen in the video i rev it a bit, then the rpm drops to about 0 and the battery light flashes for a second but the car doesnt actually die.

Anyway, i plan to take the car to a workshop/garage this month to solve this issue however if i can do this at home id be excstatic.

After searching the forums heavily ive come to the conclusion that it may be caused by one of, or a combination of the following:

-faulty afm

-leaking i/c piping

-dirty aac valve

-faulty o2 sensor

-faulty tps

Ive read that cleaning the aac valve can do wonders; is this the type of problem i can solve by cleaning the aac valve at home? It's just that i dont have a large amount of cash to wave around so being able to fix this my self would be great.

Link to comment
https://www.sau.com.au/forums/topic/199778-is-this-idle-hunting-bad-idle/
Share on other sites

if not a factory computer, this can be caused by having the first few cells of the map unbalanced, ie on powerfc first 3x3 should be the sameish in fuel and timing, otherwise you get this sort of thing as it jumps through bouncing off different values.

if standard ecu, check your afm wiring and plug, and if all good try cleaning or getting a replacement aac valve

mine did this when rolling up to a set of traffic lights in neutral

it was the AAC valve. You can check this by temporarily disconnecting it. if ya idle doesnt fluctuate after disconnecting it, well theres ya problem

i ended up putting on a sr20 aac valve that was apperantly the same and doesnt do it anymore.

I had the exact same symptoms as you after pulling everything apart for a turbo upgrade (pulsing idle when stationary with car warmed up). In my case it turned out to be an air leak. Check all vacuum hoses connected to the crossover pipe and intake manifold for broken/split ends. Also check your Intercooler piping and make sure there are no leaks after the AFM. Definitely clean your AAC Valve regardless as many have mentioned.

Gave the AFM a good clean today, the inside was full of black shit. Gave it a clean with some electrical contact cleaner and put it back, the car seemed to run better than before. It still has a rough idle at times but its not as frequent.

Tomorrow i'll be cleaning the aac valve, hopefuly that helps.

  • 2 weeks later...
In the video you can see that my idle is fluctuating from about 100-1000rpm. This occurs when ive been driving the car for around 5-10 minutes, or generally once its all warmed up properly. You may also notice that as the rpm fluctuates, so does the vac/boost.

I have the same thing. At first I thought it was a Vacuum leak, but after testing with soapy water and listening with a hose I found nothing. Now I suspect it is a faulty O2 Sensor. When the car starts idle hunting try disconnecting your O2 Sensor and wait around 30seconds. When I did this my idle stopped still at 900rpm.

My theory is that the car runs fine until the O2 Sensor is warmed to operating temperature as the ECU ignores this reading until that time. Once the O2 sensor is operating, the ECU reads a false value and idle struggles as the O2 Sensor is not able to keep the ECU up to date with accurate readings. I tested my O2 Sensor at operating temp with a multimeter and noticed that it does not vary in voltage as it should. I am going to test another O2 Sensor. Will let you know how it goes.

Very interesting theory. Last week i gave my aac valve a very good clean. At first it seemed like the problem disappeared but after about 30min of driving it happened but only to a small extent. No where near as bad as it was before. The aac valve cleaning definately helped.

Unfortunately, i havent been able to drive my car enough to see if the problem has gotten any better. I got busted driving it last week and got 2 fines, one for it being manual and the other for high powered vehicle (im a p-plater). Its my second car and i drive it like once a week but i dont feel like risking more fines. Im fully licensed next month though.

The o2 sensor stuff sounds like its worth a try if it happens to me again, ill keep it in mind.

thats how my car was running when i took the BOV off and turned it on LOL

so definately check for leaks in all piping such as vacuum and intercooler/intake side of things

but as others have mentioned before try someone afm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The hot exhaust light will come on not from just the cat being blocked, but it's just a temp sensor, and it's designed to warn you to not do things like park in long grass.   If you've been pushing the motor a bit, it can cause the light to come on.   Second if the cat is rattling, I'd suspect it's not blocked, but instead falling apart inside.   The easiest "fix" until you can get a cat put back in, is to unbolt your one, bash the rest of the insides out, and then bolt it back in.   For a daily driver/street car, I am in agreeance of put a cat in the car. If it were race car I wouldn't care if it were removed.
    • No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
    • I'm not sure what sort of shops are nearby, but I'd expect any reasonable exhaust shop could put a cat in it that will not restrict the power that engine makes. Otherwise, if you want to remove it, short lengths that replace the cat are readily available online, search for "de-cat pipes" or "test pipes"  
    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
×
×
  • Create New...