Jump to content
SAU Community

Recommended Posts

My car is finally going in to be tuned by Mercury Motorsports next friday the 18th and I just felt like sharing my excitement with everyone, lol. its been a very expensive 4 months and I will be happy with 270rwkw, although I am told they might be able to get 300rwkw out of her with the mods I got. And I hope to make the motor last as long as possible.

I plan on running around everyday on 9psi and cranking it upto whatever they tune it to when I need the extra grunt. I know 300rwkw is nothing special, but for me its 4 months of pain and suffering paying off finally. I will be at the East Coast Customs dyno day and I cant wait to hear it screaming away on the dyno with new turbo.

anyways, hope to meet a few more of you around the traps when I finally get back out and about :D

Edited by Spooner
Link to comment
https://www.sau.com.au/forums/topic/200696-excited/
Share on other sites

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

haha i am in the same situation as you man.

I havent been able to drive my car since february last year. 5 months waiting for my car to get out of the workshop, and now its at a dyno to see what happens.

300rwkw is my goal being still standard internals, but have a forged engine getting done at the moment.

Been fairly stressed out most of the time hahaha, but hope everything pays off. Best of luck for your car.

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3569997
Share on other sites

so what did you get done to your car?

Garrett GT3076r with .82 ex housing

Custom intake and dump pipes

Full exhaust turbo back with jasma mufflers

hks pod filter

front mount

nismo 740cc inj

z32 afm

turbomsart fpr800 fuel reg

walbro fuel pump

apexi avc-r

apexi power fc

thats about it for now

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3569999
Share on other sites

You have all the parts to make it... You will get 300rwkw at around 19 psi no worries on stock head and cams...

yeh i just going to be happy with anything over 270 atm until something breaks and i can throw in some forged gear. and do some head work

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3570758
Share on other sites

good to hear buddy, hope it all goes to plan. mine should be rolling on the road soon after yours. but not that much power to start.

nice one. u must be cheering hey?

its relieving to know i'll finally be at the point of achieving the first stage of the build up. most of the work was done by my housemate and myself. I got the intake and dump pipe done at Predator. so its good to know that some of my own blood and sweat has gone into it.

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3571258
Share on other sites

nice one. u must be cheering hey?

its relieving to know i'll finally be at the point of achieving the first stage of the build up. most of the work was done by my housemate and myself. I got the intake and dump pipe done at Predator. so its good to know that some of my own blood and sweat has gone into it.

Yeah mate, fresh rebuild most of the things under the bonnet will be new. or near new. and alot of my time and time of people helping me has gone into it. it has been a to two workshops, once for painting and the other for piping, wiring, and some more. but the rest is and will be done in the shed.

i hope it makes it more satisfiying when i drive it.

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3571431
Share on other sites

sounds like a good set up, if your expecting that sortof power from yours can i get an opinion on wat sortof power i might get out of mine:

kkr430

gtr injectors

splitfire coils

z32 AFM with 3in intake

FMIC

full 3in zorst

sard fpr

apexi pod

bosch 040

apexi avc-r

and will be tuned standard ecu by dr drift

i was thinking about 220kws out of the rb20det on hopefully 16psi

anyone think i might get more

Edited by Catlin
Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3571497
Share on other sites

sounds like a good set up, if your expecting that sortof power from yours can i get an opinion on wat sortof power i might get out of mine:

kkr430

gtr injectors

splitfire coils

z32 AFM with 3in intake

FMIC

full 3in zorst

sard fps

apexi pod

bosch 040

i was thinking about 220kws out of the rb20det on hopefully 16psi

anyone think i might get more

apexi avc-r

and will be tuned standard ecu by dr drift

i reckon you would get between 220 and 250rwkw. I knew someone up the coast with that turbo, full aftermarket ecu, 850cc injectors, z32 etc making about 275rwkw on an rb25

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3571624
Share on other sites

Its always great to do the work yourself, I hope you get your power but are you aware that over 250kw they are prone to failure? The ringlands are the weakest link in a stock motor but when they fail it is not usually horrific, I have run mine at 370hp (280kw) but with water/metanol for safety, it reduces pinging and gives me much smoother boost.

Good Luck and keep us posted.

Here is a pic of busted ringlands, the motor was sweet except for this.

post-17300-1199862791_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3571722
Share on other sites

sounds like a good set up, if your expecting that sortof power from yours can i get an opinion on wat sortof power i might get out of mine:

kkr430

gtr injectors

splitfire coils

z32 AFM with 3in intake

FMIC

full 3in zorst

sard fpr

apexi pod

bosch 040

apexi avc-r

and will be tuned standard ecu by dr drift

i was thinking about 220kws out of the rb20det on hopefully 16psi

anyone think i might get more

i am going to be running that turbo on the 25, with z32, fmic, zhaust, nismo fuel reg, nismo fuel pump.

forged engine though, on 10 psi i want 230ish rwkw. so you should make a little less then that on 16 ish. Dr Drift(sam) will let you know where the car in comfortable to run it at.

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3572258
Share on other sites

Hey man

300kw nothing special? I just started out and had my first dyno ever yesterday. Got 122kw atw for an auto R33. If i had 220kw atw i would be giggling daily. Congratulations mate, glad you achieved your goal. Must be happy times round your place. ;)

Link to comment
https://www.sau.com.au/forums/topic/200696-excited/#findComment-3572960
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...