Jump to content
SAU Community

Recommended Posts

underhand grip doing rows puts the wrists in a bent back position.

and using a straight bar means they are bent back and twisted out. Then from there they get pulled upwards by the arms, and downwards by gravity.

Use double overhand grip.

either thumb under or over to see what works best.

cheers, makes sense as to what the issue could be.

Bought commercial cable cross over for $100, a second corner cross over unit for a friend of mine for $180, laying down back row for $90, commercial peck deck for $20 (that's right, $20) and a commercial ab crunch machine for a friend for $20. If I had more space, or had known that it was going to be that cheap, would have organised some storage space and bought a lot more. couldn't believe the prices. will post pics tomorrow once I have it either in the work bay or hopefully at home. the $100 is missing the cables that go with it, so will have to source them somewhere, but that's easy enough.

Having seen your dumbell racks I'm guessing you'll be charging membership fees for your garage soon...

I wish I had seen this auction before I bought all my gear. Would have saved thousands

Full commercial power rack went for $180. It was ridiculous.

Worst marketed auction ever. I only saw it on gumtree and decided to pop in see what was there. There were about 30 people there, and they were all looking to privately buy equipment for their homes.

A lot of the gear was very badly presented as well, covered in dust and some of it in mould, with scratches here and there, but it was still fully functional.

I will post pics by end of the week once I get it all home and cleaned up and assembled.

I think I get away with no wrist issues due to using bitch gloves that wrap around and support the wrist a little.

Just buy a proper pair of wrist wraps from the likes of Inzer or Titan and wrap them properly before a set.

If there is still pain you might need some fascia release or treatment on the muscles or tendons.

IMG_1631.jpg

finally, a pic appears.

going to have to move the tv cabinet thingy and fan out and put the pec dec there and will wall mount the tv above the dumbbell rack.

have sold the calgym chest press, and am now already a few hundred ahead of what I paid for all the gear. wish I had bought more....

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Haha yea it's a bit of a weird setup at the moment, just wanted to make sure I sorted out any headaches before dyno day. At the moment I've changed the exhaust manifold, turbo and downpipe, 460lph fuel pump and rising rate reg as well as the previously mentioned headstuds and gasket. The nistune was already mapped for the car as it was and drove around for a few months no worries. The plan is to run flex fuel hence the big pump, which I've wired direct to the battery through a relay to avoid voltage issues.
    • Um. Was the ECU the same as the one previously there? I know R33's needed R32 GTST ECU's or other tomfoolery to run Nistune. This is such a wild setup. Most people would plumb in the turbo then not drive the car (i.e tow it to a tuner). What's actually changed since it last ran?
    • I'm a bit stuck with this one fellas, I recently decided to undertake a turbo conversion on my GTS-4, ended up pulling the motor to replace all the seals and do an mls head gasket and arp head studs while I was at it. Everything has gone according to plan, no oil or coolant leaks, compression checked out, and decided to give it a test before I book it in for a tune As it stands right now, the turbo only has oil lines plumbed so that I don't put boost into my untuned engine, and I'm using the factory GTS-T crossover pipe with a maf and poddy as a temporary intake. The car starts with relative ease and idles amazingly, however as the title suggests it really doesn't want to rev up, runs very smooth but almost feels choked out and unresponsive to the throttle, almost like it's running lean or something? I've triple checked my vacuum lines and timing with a timing light, injectors haven't been touched as of yet to avoid flooding the engine and worked perfectly beforehand, new plugs and coilpacks, I've even unbolted the cat just to see if it spontaneously collapsed, no dice The car currently has a nistune r32 gtst ecu installed so I have no way to check for fault codes. At this point I'm a bit stumped. Is this normal behaviour for a car with a turbo bolted onto the exhaust going nowhere? I'd imagine the turbo wouldn't cause this much restriction in the exhaust without the boost going through the intake. Any ideas? If necessary I can link a video of how it responds to full throttle while in neutral.  
    • Insert tab A into slot B?
    • Instructions seem simple enough to understand.....
×
×
  • Create New...