Jump to content
SAU Community

URGENT! part needed or how to fix!!

dru32

By dru32,
in General Maintenance

 Share

Recommended Posts

dru32 Collaborator

dru32

Posted
  • Author
Posted

ok i cleand the inside of it out and tried again.. the engine seems to turn over, but doesnt start... I am only guessing that this thing is the problem, can someone confirm this before i start looking for this part...

if it is this at fault.. would all jap sell them.. if not, who else would?

I think i would only need the part that spins around, not the whole thing.

dru32 Collaborator

dru32

Posted
  • Author
Posted
Originally posted by walkoau

its the variable cam timing unit. (i think thats what its called).

how the hell did the locating pin snap off?

you best bet is a jap wrecker.

how did i snap it off??

I realy dont know.. :confused:

I took it off to paint the cam belt cover with some left over paint from my boot lid.. I put it back on.. lined it up, and it slipped in perfectly, tightened all bolts,... went to turn my car on to move it back into a sunny spot to tack sum engine bay shots and the car didnt start.

thats the only thing i could think of that could go wrong.. so i undid it all to take a look and noticed the pin was snapped off

dru32 Collaborator

dru32

Posted
  • Author
Posted
Originally posted by SteveL

It's the CAS = Crank Angle Sensor.    Not really clear what's broken off from the photo's.   Shouldn't be too hard to get one from a wrecker.  If you really get stuck I think I've got a spare somewhere, but I'm in melbourne.

the thing that is broken off is the little metal thing laying on the "cas" in the second photo. it broke off from inside the ??? hole :uh-huh:

SteveL Mentor

SteveL

Posted
Posted
Originally posted by dru32

so would this be the reason why the car wont start?

Yes...it tells the ECU info about injector an ignition firing points/crank position. Somethings obviously not lining up properly any longer. The internally splined 'shaft' engages with similar shaft bolted to the end of the ex camshaft. If it's not in the right position, then ign timing etc will be out.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB20DET lean on cold start

      By GTSBoy · Posted

      You shouldn't need to massively fatten up the mixtures for cold conditions. For one thing - 0°C is not that cold. For another, the Haltech will be using the IAT sensor to tell it how dense the air air, and calculate the correct amount of fuelling. Then the cold start enrichment is added as a % on top of that, so it should scale with the main fuelling. You might also doubt the IAT sensor at this time. You're not using one from an RB26 are you? Using a nice Bosch sensor or similar? Happens. Some wideband units take great pleasure in killing their sensors. Put another wideband in the tailpipe and compare. Or just swap the sensor to a brand new one and see.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Oh, my misunderstand. When the car was running, it sounded ok, but if I gave it any gas it wanted to die but caught itself afterwards. It's very different from how it was a couple months ago when it was warmer outside. The logs show that the AFRs are better during, what I assume, is warmup enrichment. Because it's cold, and air is more dense, should I work on the enrichment bit?
    • A31Skyline
      Rb20e and RB20DET parts

      By A31Skyline · Posted

      yess of course im not using 2nd hand parts from my spare engine, but the place where i live is hard to find parts for the RB20DET ,but for the RB20E is everywhere including new ones and a lot cheaper ,because for the RB20DET you have to order it overseas to get one and it cost a lot of money 3x the price to be exact. so i ask this topic because if i can use the new ones but for RB20E is it compatible or not. if not im screwed haha, not totally screwed but i have to save a lot of money first before i can begin repairing my engine, thanks for the information before.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Unless my sensor just died, was only a couple months old, I strongly believe it didn't. How can I test it? I never mentioned it being 20:1+?
    • GTSBoy
      Rb20e and RB20DET parts

      By GTSBoy · Posted

      Well, you wouldn't use 2nd hand bearings out of another engine anyway....so just buying the proper bearings is obviously what you're going to do. The crankshaft would be common. The conrods might be common. There is essentially nothing else you would be able to use.
×
×
  • Create New...