Jump to content
SAU Community

Recommended Posts

Why because u drive a liberty?

possibly..

but more so that people still go and hang out with defectable cars at locations and do shit to attract attention, then get done.

then complain.

I can't wait till the first aus car crushing.. :D

Just for you qld people...

I worked at QPS for 11 months as an IT contractor.

Believe me when I tell you this.

They have accounts on every single online car forum you could think of.

They organise these little "stings" as you guys organise your cruise/meetups.

They will leave the charity cruise things be, but anything like "blah blah carpark meet and cruise to blah blah", will more then likely end up with internal paperwork being started to organise the required cars/man power/equipment required to defect you for your headlights that aren't alligned.

I just think it's funny that people still don't learn.

but yes, it's because I drive a liberty :blink: Poof!

I have the bottom end and the head/inlet setup at the shop will be building them up over the next few months.

Atm i want to get my 25 gearbox conversion done so i can hit the track with the 20 a couple of times before pulling it out and slotting in the 2630.

Will take me till the end of the year i think to get the new motor finished. I have the head/inlet and the 30 bottom end at the workshop will build those after the gbox conversion is done and i have had some track time.

Also looking to get a mod plate for my 2 seater conversion, where is a good place for that?

Oh and im puttin my stock bov back on in the next few hours that should make u happy ;)

Edited by 2630GTS

haha you bet correct, looking at making a box for it like iceberg but i might just hold off and do one for the 2630. Something like the one in this pic

im not sure if having an unshielded pod is a defect so hopefully ill be right (maybe i should call transport)

post-4425-1200286780_thumb.jpg

Edited by 2630GTS

As I understand it they don't issue you a defect because your car is defective, they issue it because they think your car might be defective. The trip over the pits is to confirm or deny their suspicions, at your cost and inconvenience unfortunately but that's the way it is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nothing wears "the most". Different cars will always show signs in a different place. 114000 km is either nothing at all (as in, given the calendar age, nearly brand new) or it's completely unbelievable. We stopped believing numbers like that about 15 years ago. Having said that, my car is up around 270000 km and I have put bushes into some places** as many as 10 times in >25 years that I've owned it. ** FUCAs, which are different on an R32 than on a 33, so not likely to be the same issue for you. I have original ball joints all the way around. They are perfectly fine. Same with the spindle bearings in the front. Tie rod ends have all been done at least once though. Pretty much every other bush in the car has been done at least twice. Some of those in the first 100000km after I got it (which was at a genuine 23000!). Some of those bushes are now sphericals, and they are on a <cough> regular maintenance schedule, hence why my FUCAs have been rebuilt so many times. Half of those 10 in the count above would be in the last few years! 'twere I you, I would budget on replacing everything, for fun and prevention. If they really are 30 year old rubber, they will all be unpleasantly aged in one way or another. Whether that's corrosion of shells, or the rubber cracking, or sagging under the load, etc etc.
    • Tighten until it starts to get loose again, then back off 1/4 turn?
    • Do them as you'll find when you remove them they are perished/dried.    Its probably one of the best things to do as makes the car so much more responsive. Do ball joints while there too.
    • Hi All Got an R33, about 114,000km on the clock.  Handles very nice, no signs of issues.    Engine is out and i'm doing an underbody refresh, mainly painting subframe, cosmetics etc. Can't see anything physically giving play, but I'm wondering which bushes are the ones that wear the most, or the first ones that may give problems down the track? For good measure I'm thinking to fit new ones. Thanks
×
×
  • Create New...