Jump to content
SAU Community

Recommended Posts

SOLD

Item:12" Kicker Solo-baric L7 Dual 4ohm with Kicker Slot Ported Enclosure

Age: ~3 Years (got it in jan 2006)

Condition: Very Good, see photos below

Price: $400 Firm PRICE DROP TO $350

To Fit: Most cars, not too sure about 200sxes

Location: Liverpool, NSW

Comments: Don't buy it if your planning to run it off a Class A/B amp, I don't want to hear people saying it sounds sht or the voice coil is fried because they've clipped the sht out of the sub.

post-22311-1200823396_thumb.jpg

post-22311-1200823422_thumb.jpg

post-22311-1200823621_thumb.jpg

post-22311-1200823651_thumb.jpg

Edited by johnnilicte

What size is it ? ive been looking for another one ..

It can be ran on a a/b class you dont need a d class amp

Dont forget that an a/b class amp that has 750wrms will obviously be a quality amp ..

What size is it ? ive been looking for another one ..

It can be ran on a a/b class you dont need a d class amp

Dont forget that an a/b class amp that has 750wrms will obviously be a quality amp ..

That true Mick, but you do get n00bs that try to run quality subs off Weconic amps, fry them, then blame you for it. I had bad experience before when i sold my JL W3v2, the moron ran it off a Sony xPlode amp and fried the coil feeding it bs power and obviously clipping the crap outta it.

box dimension plz bud.. nego on price?

I will measure it once I get home, but it's the length of one suspension tower to another in my 180SX, and sits just higher than the parcel tray.

Price wise kinda, but if you have anything of interest to trade I would drop the price of course.

I think they want the size of the box..

Edited by johnnilicte

$400 firm, I haven't measured it yet, coz my car died as per thread in the Forced Induction section!

74cm wide x 37cm high x (39cm deep at top x 47cm deep at bottom)

It's a 12" inch sub

i had one of these in my VL... serious power for only 1 x 12inch! Not poppy bass like sony and pioneer... nice deep boom and seriously vibrates the fv ck out of everything in the car;) Have to hear it to understand..

Good luck for an awesome sub:)

Any offers? I'm kinda buggered for cash... Still need to get my 5-stud conversion and new tyres before the motorkhana with ozmazda next week

thanks boys (maybe girls??)

I know they're great... :)

Just downgraded to something smaller in a sealed box... time to get the boot back.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Apologies, while id like to put the MAF as close to the TB and relocate the recirc, this may be too much work. Will most likely end up just putting it on the original AFM spot ( onto/next to the airbox ).  Was going through nistune, found a pretty nifty doc on this. Nistune MAF Notes. Also, i was looking through the bay, and there seems to be a tube/line connected from the A/C to the intercooler piping ( Between the smic and the recirc), what does this do as the crossover fmic piping doesnt have any connection? plumbing? not sure what you call it but the nipple thing ahah.  Also, been reading up more about crossover fmic in regards to the legality of having the hole drilled for the piping, this would most likely need to be engineered right?
    • My advice is if you need a big build done do it in Japan. The yen rate is so favorable and there are shops that can be genuinely trusted and not micromanaged/carefully monitored every step of the way. Garage Yoshida is obviously my preferred option but they're so busy these days and all interaction with new customers has to be mediated through BBL/Toprank now. 
    • I haven't....but a poorly made one would terrify me. Surely a good second hand one is the go, as they don't work hard and no-one wants to keep one after they are finished with it A big consideration would be the weight of the shell you are putting on it....is it a fully dressed chassis or just the body
    • Not stock. All remade. Mostly looks stock because the pipes run to and from the standard holes in the inner guard to get to the return flow FMIC. I'm not sure which question you're trying to ask, because it seems like "stock position" vs "stock position".
    • Hey, it's a GT-R, it's just as significant a moment as mine😁 It's not ideal when things are uncertain; I'm the type of person that always has a set plan for things in life so being unsure of this plan puts me in a weird place mentally.
×
×
  • Create New...