Jump to content
SAU Community

Recommended Posts

  • Replies 94
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

good luck !

Up date after the races

The car having some boost isues, could not get over 20psi. I think its the cheap Ebay waste gate, but on 20psi I was able to run 7.1sec in the 1/8. Best 60ft the car had for the day was 1.50 sec. Then "Bang", i broke the outer CV joint in the rear. The car is HOOKING!!!!

So i now have to resolve my boost issues and change the CV joint. I will look into some performance ones.

Up date after the races

The car having some boost isues, could not get over 20psi. I think its the cheap Ebay waste gate, but on 20psi I was able to run 7.1sec in the 1/8. Best 60ft the car had for the day was 1.50 sec. Then "Bang", i broke the outer CV joint in the rear. The car is HOOKING!!!!

So i now have to resolve my boost issues and change the CV joint. I will look into some performance ones.

what you can do is get a gtr rear end, strip all the arms, diff, cv's and bolt that to the existing cradle in your car now.... you will need a custom tailshaft

the diffs are mechanical, also are a 4.11 ratio, the cv's are a shitload thicker and stronger, this is what i have in my rb26 powered s15, yet to test but ive had the cradles side by side and the difference in everything you will swap over is heaps better that the s14 stuff...

waldoforce You don't have gtr diff+axles+hubs? Was a miracle that you run with gts-t or silvia rear end!!!

I have gtr diff,axles,hubs and the center shaft!!

You need hubs because gtr axles are thicker!!

You run only 1/8? Not 1/4?

Any issues with gearbox?

Your twin plate work good?

Fotos? Videos? :P

1.5 is very good :(:)

I have Mickey Thompson 26x11.5x15 in 8" Weld Drag lites wheels!

What rear shocks you have? Do you have any aftermarket links on the rear? Bushing?

Do you have skinny front? I have 18" front for the time with 8piston D2 brakes :wub: I don't know what to put there..

waldoforce You don't have gtr diff+axles+hubs? Was a miracle that you run with gts-t or silvia rear end!!!

I have gtr diff,axles,hubs and the center shaft!!

You need hubs because gtr axles are thicker!!

You run only 1/8? Not 1/4?

Any issues with gearbox?

Your twin plate work good?

Fotos? Videos? :P

1.5 is very good :(:)

I have Mickey Thompson 26x11.5x15 in 8" Weld Drag lites wheels!

What rear shocks you have? Do you have any aftermarket links on the rear? Bushing?

Do you have skinny front? I have 18" front for the time with 8piston D2 brakes :wub: I don't know what to put there..

enjoy! Oh take some time and look the time slip in the vid. Thanks

I have R33 GTST diff, axles, the whole rear sub frame.

I will look into the GTR axles and hub, thanks.

No issues with the gearbox as yet and the twin disk clutch is still holding.

The red 180sx in the vid is using almost the same tires that you have (26*11.5*16 ET Street drag) , but he has them on the twin turboZX 8.5" rims. I am using MT 26*10*15 on 10" weld rims.

In the rear I am using stock S14 shocks, with lowered skyline springs.

Yes I do have adjustable aftermarket links in the rear, with polyurethene bushing in the spindles. I also have a set of aluminum rear subframe spacers

No i dont have skinnies up front. I have 18"s awell with the factory skyline brakes and rotors all round. You will be fine with them. I have seen many 10sec cars without skinnies up front.

what you can do is get a gtr rear end, strip all the arms, diff, cv's and bolt that to the existing cradle in your car now.... you will need a custom tailshaft

the diffs are mechanical, also are a 4.11 ratio, the cv's are a shitload thicker and stronger, this is what i have in my rb26 powered s15, yet to test but ive had the cradles side by side and the difference in everything you will swap over is heaps better that the s14 stuff...

Thanks, I will definitly look into this. I need something that can handle my hard launches.

Thanks again

1.506!!! Very very good ;)

But 7.1 isn't :dry::( 600whp s14 must do something like 6.5!! Try more when you fix your boost problems ;)

My tires are better than your friend's... I have 15" so quite more sidewall!! My tires is et street drag too.

Don't forget that your need also gtr hubs.

What times did your friend and what horsepower he has?

I will put also a line lock for easy burnouts!! :D

My target is to do very low 10sec in the 1/4 drag races!!

We have a race at 13 September and I hope to have my car ready to race :)

1.506!!! Very very good ;)

But 7.1 isn't :(:) 600whp s14 must do something like 6.5!! Try more when you fix your boost problems ;)

My tires are better than your friend's... I have 15" so quite more sidewall!! My tires is et street drag too.

Don't forget that your need also gtr hubs.

What times did your friend and what horsepower he has?

I will put also a line lock for easy burnouts!! :D

My target is to do very low 10sec in the 1/4 drag races!!

We have a race at 13 September and I hope to have my car ready to race ;)

Thanks for the heads up on the GTR hubs.

My friend makes about 480whp and his best time to date is 7.1sec in the 1/8th.

You are right, at 600whp I should be able to do 6.5-6.7sec, but I am not the best of drivers :dry: . We have an event at the end of this month. I will have the car ready for that.

  • 2 months later...

The car finished!

We had a problem with the wastegate.. the valve was all the time semi-open and we didn't undestand it.

With stock ecu and mafs was a pain. The car was very unfriendly and difficult to drive but maybe the problem was the semi-open wastegate.

We did 11.7 with 1.3bar only and the clutch slipping a lot!! But I wasn't sure that it was slipping...! Ah and 1,565 60foots!!! And without launch control!!!

So we take the desicion to put an Apexi Power FC D-Jetro! And we check the wastegate if was good and we saw the problem.

So when we put the power fc the car was like a stock car!! Very friendly!! Still with base stock map(ofcourse only for vacuum driving)!!! I was so happy when I put the power fc but as I said maybe the problem was the wastegate. We burn two z32 mafs while we tried to finish the car with stock ecu so I am very happy now with the maps and I have cool engine bay!!

We was on the dyno.. at 16psi 540flywheel hp with 8500rpm limit and the clutch slipping a lot!!! The afr was 11.0!

So we leave it there... with 2.2sec 60foots and with 16psi boost and with this bad clutch the car did 12.5 in my second drag race! I go for race only for fun as I had slipping clutch.

I put also Splitfires just to be sure.. Gizzmo launch control system with tach recall shift light.. Denso Iridium IK24 plugs..

When I will buy an overhaul kit for my OsGiken Twin plate I will go again on the dyno. Maybe with IQ27 if I will have money :cheers:

Also I use 100octane pump fuel. But I am thinking to add 1/5 Vp Import for my high boost runs. How much high? I don't know yet :D

Edited by GreeceS13
any update ?

Thanks everyone for the info on the GTR axles and hub, they work like a dream. I am now hitting 1.4s 60 foots, best to date is 1.47sec. Also, I have been able to get the boost up. I am pleagued with a faulty waste gate, but was able run 26psi. The car did 7.003sec in the 1/8 on a test and tune night with minimal track prep. We have an event today. I will keep you all updated.

Hey waldoforce,

can you post up some pics of your s14, are you also able to post some spec's on turbo, cams, pistons?

cheers

dan

The turbo is a garrett T04z with a 70ar back housing. The motor has factory pistons, and I am using Tomie pon cams 260 degree.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...