Jump to content
SAU Community

Recommended Posts

hey guys you may have read my other thread about low compression across all 6 pistons well, i have checked everything i know.

i pulled the cam covers of and put a spanner on the nut part at the front of the cam and gently pulled on the cam and held the cam gear to see if there is movement between the joins and i have nothing on the exhuast cam, on the inlet cam with the variable valve timing cam gear i did they same and i had a inch of movement is this correct

Link to comment
https://www.sau.com.au/forums/topic/202897-help-needed/
Share on other sites

lol

did you post a thread about this before ?

I think i told you to check the cam with a shifter? pull the gear off, your locater might have snapped like mine did the other day, if you keep driving it like this it could destroy your engine.

Pull it appart and be carefull when doing so cos the pin that snapped will fall into the timing case and you dont want that to happen cos you will need to get it out!

Yes this is what i said.

YES the cam gear can move on the cam, if the dowl locator snapps on the cam then what happens is that the gears are still in time but the cam is retarded, this happened to my engine and it had 30psi in all cyls and it still ran as well.

Take the harmonic balancer off, take the timing covers off and put the engine on TDC and make sure the bottom timing mark is correct as well as the top ones.

Get a shifter and put on the cam (you need to take the cam covers off) and try turn the cam gently. If the cam turns without the cam gear turning then you would have snapped the dowl and it might only be a little bit out. It can get worse and if you dont fix it now it could slip around and smash valves.

This is what to do next.

1: PUT A RAG OR A DRIP TRAY under the engine because oil will leak out of the front of the cam

2: You need to take the 4 really small 8mm bolts off from the front of the inlet cam, it is spring loaded and lots of oil will come out.

3: undo the 19mm bolt that holds the cam in (it might be loose but undo it BEFORE taking the timing belt off because that way the gear wont spin when trying to undo it also use the spanner to hold the cam in place)

4: remove the bolt and the gear CAREFULLY, you should find the little locator snapped inside the gear, when you remove it as soon as it slips of the cam tilt the front of the gear that goes over the cam upwards so the bit does not fall out.

5: inspect cam, you will find that the locator is snapped.

You will need to buy another cam to fix this or get someone to drill out and replace the locator on your existing cam. I purchased a new cam.

The GOOD news is the engine is not buggard, the valves have not hit YET.

Replace the cam and the timing belt while your at it and make sure the head is not scored on the first cam cap if it is rub it back with some 1200 sand paper till its smooth again.

Edited by Guilt-Toy
Link to comment
https://www.sau.com.au/forums/topic/202897-help-needed/#findComment-3601145
Share on other sites

you cant be serious? the cam gear wont move on the cam unless its loose or snapped, can you see the dowel in the cam?

are you sure ?

Look at the cam, it should have a little pin sticking out of it and if you look inside the gear you can see where the pin is supposed to go, if its snapped the face of the cam will be flush, if not you will see it sticking out.

take a clear pic of the face of the cam, and send it. the locator pin will have to be broken if the gear is moving on the cam.

Was the 19mm cam bolt tight ?

i just finished pulling both cam gears off and guess what no snapped dowels :(

i really dont know what to do ????

thanks guilt-toy

Edited by Guilt-Toy
Link to comment
https://www.sau.com.au/forums/topic/202897-help-needed/#findComment-3602583
Share on other sites

hey guys pulled the head off yesterday because when i was checking everything i noticed that a exhaust manifold nut was loose, i tried to tighten it but the stud was really loose in the head i then noticed a shit load of oil all over my block and guess what......i only got all my manifold bolts replaced 4 months ago and the wankers drilled right thought to number 1 tapppet ill take a foto and show u all

Link to comment
https://www.sau.com.au/forums/topic/202897-help-needed/#findComment-3607218
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To be determined, Luke, to be determined. 馃榿 Definitely the car
    • It might be worth having a good look at the chassis behind the bumper then; most people prefer the series 2 look so it might have been changed to cheaper parts as part of an earlier repair
    • The car itself a series 2. I was just curious about the headlights and just wanted to confirm that they were series 1. Good to know the rest of the front end is series 1. It鈥檒l be easier for me to find parts on the aftermarket side of things lol
    • If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
  • Create New...