Jump to content
SAU Community

Recommended Posts

Hey guys just after some proffesional clarification as I find this a tad confusing. I have an 2000 model R34 non turbo that is 2 door but AWD. A mate of mine beleives it is a GTS4. Now from reading this I understand that i need GTR suspension? is this correct? or is there R33 suspension that is suitable for me? Basically I just want to lower my car and stiffen the ride and have been told that coilovers are my best option. Its not a track car or anything so it doesnt have to be brand new or top of the line gear.

If anyone could help me out I would really appreciate it.

Cheers.

Unfortunately R34GTS4's are not the same as anything else. So you can't just grab a complete kit, it's a mix and match exercise. Being a 4WD the front shocks have to be the short style, like an R32/33/34GTR. But it doesn't have the same weight on the front (no turbos, no intercooler, smaller gearbox etc) so you need a lower front spring rate and lower spring free height than an R33/34GTR. At the rear the R34GTS4 doesn't have the alloy rear hubs that R34GTR's and R34GTT's have, it has cast iron hubs like an R33GTST and R34GT. That's why an R34GTS4 needs the rear shocks with the eyes (like an R33GTST) not the forks (like an R33/34GTR). The rear springs in R33and R34 all models are the same.

A summary of what you need;

R33/34GTR front shocks

R33GTST or R34GTT front springs

R33GTST rear shocks

R33/34GTR, R33GTST or R34GTT rear springs

Cheers

Gary

  • 3 years later...
  • 3 weeks later...
  • 3 months later...

Okay so i have a sedan 1999 R34 25gt-v.
What are my options here?

It is an N/A but i'm almost one hundred percent sure that a gt-v has the exact same suspension set-up as a gtt.
Therefor giving it the eye fork set-up i guess.
I assume from the previous posts i cant transfer coil overs from a coupe into my sedan?
Are there any previous model skylines ie. r32/r33/ coil overs i could purchase that i could just drop straight in?

Any help would be much appreciated :)
Cheers Tony.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Once the belt slips it can very easily cause a cascade that encourages more belt slip. Check the pulleys carefully and see if the grooves have cupped. If it has it's time to replace the pulleys. If the rubber has glazed you also need to replace it. Shouldn't be shiny. From the factory there's a lot of exposed fibers(?) on a v-belt that will go away as it's broken in but some should still remain visible without sticking out significantly like a new belt. I went through this on my dad's Camry recently. It would keep slipping even after setting the tension higher, only solution was a new belt.
    • Belt polished and/or pulley(s) glazed. Rub pulleys with sandpaper, replace belt.
    • I've also got a quick jack. I would never get under my car again without using it.  While it might be quicker to use a jack and stands, it is such a quality of life improvement that I wouldn't have it any other way now.  How much slower the quick jack is to setup will be based on your circumstances. Can you leave the jack rails on each side of the garage? Can you leave the hydraulic lines attached? etc.  If you can drive the car into the garage and simply push the jacking rail thingos under the car into place, it is super quick to setup and use. But if you have to pull the pump unit out of storage, attach the hydraulic lines, wheel out the lifting rail thingos.... yeah takes a bit of time. Having said that, I would still prefer that to using a jack and stands lol. 
    • Sydney Tools have them for ~$3400. More than the Quick Lifts but these seem better. https://sydneytools.com.au/product/quickjack-7000tl208240v-5175642-7000lb-110220v-portable-light-duty-truck-and-passenger-car-lift-system  
×
×
  • Create New...