Jump to content
SAU Community

Recommended Posts

Here is a quick DIY to bypass your factory amp in the rear of the car.

First things first, you will need the following to do this.

wire cutters

saudering iron (not needed but reccomended for a clean install.

electrical tape or heat shrink tube

1) Disconnect the white clip in the back of the factory amp. The amp is located underneath the rear shelf in the trunk. It's a bit tight to get in there but get used to it because you will be there for a while. My amp looked like this (1A) but I've heard they come in various sizes. Use your common sense here and you will be able to find the right one.

1A

DSCF1735320x200.jpg

2) Next, we will be cutting the wires one by one on the back of the clip and attaching them togethor (DONT DO THIS YET!!). Now to attach them, you can sauder or twist them or use butt connectors... whichever you feel like doing. But make sure the connection is solid and won't come apart.

Refer to this picture for the following steps!!

DSCF1786640x480320x200-1.jpg

Now make sure your clip is facing the same way mine is. Look carefully at the notches in the picture and the direction of the holes. THIS IS VERY IMPORTAINT! Also I would suggest doing this 2 wires at a time, so you dont loose track of which wires are which.

3)First two wires to cut are the numbers 1 and 3. Cut them, and sauder the ends togethor. Don't forget to put the heat shrink on before you sauder.

4)The next two wires are numbers 6 and 8. Again, cut them off at the back and attach them togethor in your chosen method.

5)Next two wires are 2 and 4. Cut them, attach them togethor.

6)The last two wires are 7 and 5. Attach these two togethor.

You should have a few wires left over but we are only concerned about 1-8. Don't worry about the numbers 9-12. Just cap them off so they can't touch anything.

If you followed these instructions correctly, your amp is now bypassed. Have fun listening to music through good speakers. :-D

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/203299-r32-factory-amp-bypass-diy/
Share on other sites

  • 8 years later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • ...oops. forgot the TCU end...
    • No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...