Jump to content
SAU Community

Recommended Posts

"This Sequential Blow Off Valve makes a great unique shrill, whistling sound instead of the usual boring "whoosh". Not only does it make great sound, but it also looks good, and is suitable for all horsepower applications. The way the valve in these SQV's works is different to most other valves on the market. The boost running through your piping when your car is under load actually holds this valve shut. So the more boost you run the tighter this valve is shut, resulting in no boost leaks. Other "push" type blow off valves that operate off a spring can often leak under high boost applications, especially at old age. This is the main feature that makes the Sequential Blow Off Valve so popular in all Race, Drag, Drift and even Show applications thanks to its looks.

$249 for BOV. $65 for R33/34 adaptor. Deduct 10% if a member of the Autoworx Club."

Does this make the same sound as a HKS SSQ? are they as good? and noob question, but are there different types of (atmosphereic) BOV'S that stall as much?

thank you

Link to comment
https://www.sau.com.au/forums/topic/203375-sequential-bov/
Share on other sites

ya i got one

>< if u give it a slight rev 'trying to climb a steep drive' u can stall it

but they sound g00d

So basically as long as you keep your revs up more than usual while uphill, it's fine?

And my question: is the sound the same as the HKS SSQ BOV? thanks

Link to comment
https://www.sau.com.au/forums/topic/203375-sequential-bov/#findComment-3606882
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I just got to work and skimmed through 61508 and 61511. I was surprised the CSA adopted both, but neither are enforced. To recap what I read, it states that in a perfect world, they should be segregated but they acknowledge that this is not industry standard and clearly mention that they allow mixing of safety and non-safety. 61511 also mentions software segregation like AB does in their safety PLC's.   Now if only I could go back to control, let alone safety over comms. In my current line of work, we're only allowed monitoring and basic control over comms. Everything critical must still be hard wired as much as possible. 
    • I've unfortunately never been as they're on the complete other side of the continent and another country that isn't currently letting us in as easily as they use to. I even heard their stop signs over there actually say "Stop" instead of "Arret". If I decided to trek the 48h drive, I wouldn't know when or where to stop haha. Whenever I order parts from UP Garage, I order from Japan as it's cheaper. Same with GKTech... oddly enough, it's cheaper shipped from Australia then it is the US.  UP Garage Japan operates their US leg though, unlike Tomei. If Tomei JPN had the power to close down Tomei USA, I'm sure it would be done in a day. They're two completely separate entities. Tomei JPN messed up somewhere originally agreeing to its creation and got sacked big time. 
    • I asked someone about this and he told me about the Audi 1.8T engine. But I think it would be difficult to swap
    • I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
×
×
  • Create New...