Jump to content
SAU Community

Rb25det Not Starting On First Few Turn's.. Help?

nismad

By nismad,
in General Maintenance

 Share

Recommended Posts

nismad Collaborator

nismad

Posted
Posted (edited)

Hi, I have an RB25DET in a 180sx and it used to start on first or second turn, the car then sat around for about 6 months and ive only recently got around to finishing off the project, now it dosnt start for 5-6 turns and really struggles to get going, once she's going shes fine.. smells a bit rich though, so far ive cleaned the AFM, changed spark plugs and fuel pump, has anyone had this before and if so what was the cause.. any ideas?

oh and i think it might be fuel related or caused by lack of fuel as i found the plug going to the fuel pump was damaged and obviously tryed to start it several times with no luck.. would this of caused a blown gasket or somthing??.. guess ill have to check compression.. help?

thanks,

Gareth

Edited by nismad
TezGT-R Rising Star

TezGT-R

Posted
Posted

NEW BATTERY.

My mates GT-R sat in my shed for about 6 months and his battery wouldnt hold charge and struggled to start.

My battery died and it struggled to start, then after it started it would make the sound like when you turn the key while its runnin, the horrible grinding sound. Got a new battery and went perfect, started first go, no horrid noises.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Toni
      R32 GTR - Where to begin

      By Toni · Posted

      Clutch done also about a year ago got a DCS HD Single Plate. Basically done everything but touch the engine 🤣 But will definitely get a fuel pump and ECU, then start saving 🫡
    • r32-25t
      R32 GTR - Where to begin

      By r32-25t · Posted

      Fuel pump and clutch and ecu that’ll get you to about 230 or so kw, after that the sky’s the limit and the budget blows out faster then you can blink 
    • Toni
      R32 GTR - Where to begin

      By Toni · Posted

      Should add all mods on the car are done in my ownership. The car was a 1 owner in Japan and I'm first owner in Aus.
    • Toni
      R32 GTR - Where to begin

      By Toni · Posted

      Thanks GTSBoy. Did BC's so not Japanese coilovers. I've already done all the other points you mentioned besides the seat, I like the factory seats and want to keep original look. Done all the fluids and comp tests etc and all consistent and clean. Well and truly used to the power and car as I've been driving it for a few years as it is now. Contemplating next steps mainly. Preference to remain twins too. @Murray_Calavera Paying for labour.
    • GTSBoy
      R32 GTR - Where to begin

      By GTSBoy · Posted

      Hmm. I don't think it is possible. As soon as you start, you will be on the hook for all the money. $5-10k is enough to make it fragile. Here's the list of things you need to do to make it nice, and driveable. If Japanese coilovers, get them measured and tested, then decide if you're keeping them or replacing them. If low rate springs, then consider big ARBs. If high rate springs, then probably leave stock ARBs. Either way, ad decent end links. Replace and/or upgrade all suspension bushes. That's LCAs front and rear, UCAs & traction arms at rear, caster rods at front. I highly recommend GKTech FUCAs, although the step to spherical joints is a step too far for some people. Rebuild brakes front and rear. This means making sure the calipers are healthy, discs are up to thickness, hoses are replaced with braided. Add good pads and fluid. Investigate wheel bearings all the way around, tie rod ends all the way around, upright bearings at the front, balljoints everywhere. Any of these that are still original are likely to be a bit wibbly nowadays. Bride or Recaro driver's seat, with fairly deep sides. Nice tyres. Street performance wheel alignment. Or track focused, if you're not going to use it on the road. Fluids everywhere if not known to be fresh. Now, learn to drive the car as hard as it will go, before trying to add any power. Save up big $$. $5k is the minimum cost for putting a decent ECU into it. A big single, with manifold, new exhaust, injectors, fuel system upgrade, ignition upgrade, triggering upgrade, etc, is >>$10k. None of that (except the ECU) is a good idea on an old RB. You really should put head studs in it, investigate engine health (compression and leak down, real oil pressure at revs, coolant condition, etc) before even considering adding power. There's nothing sadder than the "I added boost then it shat the bed" thread.
×
×
  • Create New...