Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

jimmy m -- i think importing would be a better choice, like you say.

Hopefully the engine is all good and no problems there, and you can spend the money you have saved for a few mods or making it look nicer. As long as you have a little extra in the bank, sounds all good to me.

The best thing about the R32 is the RB20DET engines and parts are so cheap.. $500 maybe for a gearbox, $1500 for a new engine. So much cheaper than R33 major parts. All are readily available, and there are other options if you want to take them later (RB25DET, RB25DET gearbox, etc).

Good luck!

yeah as pred said R32 parts are dirt cheap theres containers full of parts coming regularly.

as for the recalls, I know one was to do with the transmission on the first batch GTS4's, and some GTRs had headlight issues. I don't have specific details as that sort of documentation isn't covered in most Jap books on skylines etc for me to read up. I do know there were 3 before 1991 August when the R32 was redesigned (sorta like a S II R33 compared to an Series 1 R33, same car, just with all the bugs ironed out).

One important thing to check with a 15 yr old car is if its had its 10 year major check done. Its sorta like a mega roadworthy in japan where almost all the important parts of the car are tested, and replaced in order to meet the standards. Most road driven 15 yr old cars hve this, so its not a major issue, but you know someones done a thorough check 5 years ago on the car.

Also pay attention to where the car comes from, coastal towns = salt corrosion, mountains = snow corrosion on the underbody.

You're budget seems ideal to getting a 15 yr old R32 GTSt. However most of the bearings and bushes on the car will have a fair bit of wear on them, so keep some cash handy for replacing them as they go.

I found my car back in May 2003. It landed here in March and unfortunately has had a hiccup after it landed and has been sitting there for 7 weeks. I should finally get it next week sometime. I am a very impatient person and have no idea how I have lasted one year waiting for it. But it will be worth the wait.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • have no doubt and wanted too trust me and may regret later not necessarily worried about weight (would be 8 kg ish total) it was more the $$ to do it properly is about $6 - $7K in hardwear need long 310mm stroke jacks etc - plus install and call me whatever im not doing it myself even if wanted too cant weld etc  - thats $10K installed vs fraction of that cost while Ive spent some money on this POS I actually really dont like doing so unless its got a large chance to make me go faster 😁 hey in still carting this things around on a 15 yr old rusted open trailer so I can spend on racing not buy a new trailer to look better the manual jacks Ive had done are heavy and take space but are transportable and usable anywhere - taking or organizing even compressed air let alone nitrogen which is more whats needed coming from Perth to Winton or Sydney or the like honestly just adds to my brain headaches/ hurts of organisation also ha 15 mins job will get down to 2 - 5 min job vs 1 min job for airjacks - all tradeoffs I spose
    • Purely out of curiosity, how do you know all this @dbm7? Do you work with automatic gearboxes professionally? This goes way way way beyond "I've had an automatic Skyline once and did some mucking around"
    • I'll just reiterate that it's best to do all the wiring diagnostics, before even thinking about buying replacement solenoids ~ that is, be absolutely sure the solenoid is bad.....ie; bad connector(s), rodents chewed through a wire, etc etc. If you don't so this, you can fork out all the money for solenoids, only to find something else is wrong (this'll make you cry if you pull the valvebody only to find a broken wire is at fault... ...some more glue on the solenoid packs -- this is the RE5R01A shift solenoid assembly.... ...these are all shift solenoids ~ ostensibly they're the same as the shift solenoids from the 4-speed auto.... ...this is the RE4R01A solenoid set... ...with these, you have 3 shift solenoids attached to the plate, and the separate solenoid is the EPC solenoid (line pressure control) -- with both designs, the TC lockup clutch solenoid (also PWM so they could slide the clutch shut), is located on the lower valvebody half.... ...(story time)...back in the 90's, it was a common fault that the EPC solenoid (or TC-lock solenoid) would fail, but Nissan only sold them as part of the assembly (think ~$350 at the time) ~ thing was, Isuzu also used these boxes in light commercials, and you could buy the PWM solenoid as a separate part, so it was possible to buy/use that solenoid (around $65), and make it fit (remove the circlip, fit to old plate and deal with wiring)...making it a more cost effective repair. I've not seen the RE5R01A shift solenoid assembly, but with the 4-speed RE4R01A it was possible to hack/fit a single shift solenoid onto an other working set, using a donor solenoid from another set with failed EPC....(by rights the whole set should be replaced), but it ends up being a question of how much life is left in the box itself ; sometimes it's a viable repair to fix one solenoid, just to get another 100k of road miles out of it before it needs first overhaul...other times the box is that old/worn, you're as well doing first overhaul and replacing the solenoids and starting fresh... What Nissan did here with the 5-speed, was relocate the EPC solenoid to the lower valvebody (next to the TC lockup solenoid), and stuck the direct-drive clutch solenoid (for the extra gear) where the EPC solenoid used to be on the 4-speed....I can only imagine they did this for serviceability ; the PWM solenoids are most likely to fail, and it's a doddle to drop the pan and change these out (as opposed to dropping the valvebody itself to get at a top mounted EPC)... ...also keep in mind, that some BMW 3/5 series & Mazda (and maybe some Ford/Mazda rebadges, not sure), also used the RE5R01A box under a different name/part number...not saying parts availability is any better, but sometimes it helps to know this when it comes to NOS floating about in the EU.... HTH  
    • FWIW, air jacks are actually pretty light and simple to add, they are just 4 hydraulic cylinders (often at the main cage A and C pillar points) and an externally accessible airline  - they make quick work a breeze
    • Maximum Attack has entered the chat
×
×
  • Create New...