Jump to content
SAU Community

R34 Injectors

Haines

By Haines,
in Engines & Forced Induction

 Share

Recommended Posts

SkylineGTT25 Contributor

SkylineGTT25

Posted
Posted

In a word NO, done the job recently and I doubt you'd be able to get the rail off without taking the plenum off and by the time you tried to do it you'd have it all apart anyway. Hardest part is getting the 3 bottom bolts (on plenum) started when putting it back together, just need a bit of patience ! And I got away without having to replace the gasket, not recommended I know but you just need to be care when spliting it.

Link to comment
https://www.sau.com.au/forums/topic/204071-r34-injectors/#findComment-3617991
Share on other sites
benl1981 Grand Master

benl1981

Posted
Posted

On an R33gtst I did it without splitting the plenum. Wouldn't recommend it unless you have to. R34 may be dfferent though, since they have top feed injectors. Get a few more opinions or check it out for yourself.

I just split the plenum, so if you want to know some tricks have a look (thread near top now). You need a set of ratchet spanners

Link to comment
https://www.sau.com.au/forums/topic/204071-r34-injectors/#findComment-3618048
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      I would again like too thank Matt for his help in me sourcing the detachable hard top for the little red car, without Matt's assistance in inspecting it and locking it down, I can guarantee it would have sold before I could get up to see it,  and as that was the only available NC hardtop in Australia, I consider myself extremely lucky on multiple levels To say I'm more that happy would be an understatement And, it is 100% water tight, I drove through torrential rain coming back south, and by torrential, they type of rain that doing 40kph in a 110kph zone was a real thing, and even then, the standing water on the Hwy was deep enough to throw waves I'm also more than happy that the huge "BEASTS" that Matt calls dogs didn't eat me for lunch, I'm sure the sniffs and licks were more to "taste test" me, over being to friendly Now to work out what colour to get it painted, panel match, or gloss black........first world problems are real
    • silviaz
      R34 GT Indicator not Cancelling

      By silviaz · Posted

      Actually I might have figured out. Looks like there is a tab according to google images but it's hidden. Silly me.
    • silviaz
      R34 GT Indicator not Cancelling

      By silviaz · Posted

      No clips on this one like the other connector. Only that red tab that I can push slightly up.
    • GTSBoy
      R34 GT Indicator not Cancelling

      By GTSBoy · Posted

      For any loom connector that has an obvious release that resists pushing far enough to unclip, just spray some silicone lube into it. You might also benefit from using a bent screwdriver or small pick to push in the right place at the right angle.
    • silviaz
      R34 GT Indicator not Cancelling

      By silviaz · Posted

      Hey all, I went to try and fix my indicator not canceling, but I couldn't remove the clockspring cable under the column so I could twist that green thin. Anyone know how to remove this cable? I see this red tab but didn't have any luck. I was thinking of unscrewing it but wasn't sure if it would cause issues. I did notice for my indicator stalk, 2 out of 3 cables were plugged in but the last cable wouldn't fit in the stalk. I'm getting it's for fog lights. It was like this when I originally pulled it off.  
×
×
  • Create New...