Jump to content
SAU Community

Tell Me What I Should Do Next

ossie_21

By ossie_21,
in WA Wasteland

 Share

Recommended Posts

ossie_21 Grand Master

ossie_21

Posted
Posted

I have a reasonable budget to work with (cash & a 6k credit card I haven't really used, and would prefer not to), but I'm a bit undecided at the moment on what to actually do. For the last 5 months I've had a bodykit sitting at home doing nothing because about a week after I got it, I got a yellow sticker I've only just managed to get off. Otherwise about 4 months ago I would have already had this on...

Work to the car to get it cleared is a touch on the expensive side (lets just say the 2 following options would have been done by now, but realistically all I can do is 1 for now), but I'm looking for other opinions on what you might do in the same situation.

a) I have a bomex front bar & side skirts, as well as some gtr rear pods that would cost about $1300 roughly to fit & paint. That would take my car from looking plain (sleeper if it wasn't for the front bar stickers) to a more "respectable" look. My current, shit, series 1 bumper has a lot of stone chips & is very scraped on the bottom of the bumper (bad experience with a driveway/mountain in Qld), and really detracts from what's behind it. Got no side skirts on the car or anything either.

b) I am running a very decent amount of power with stock injectors & cams, so if I replaced those with some aftermarket gear I'd be looking at more power, but also won't be stretching the limits of the car. With this I would probably be looking at some splitfires as well which would add to the cost, prob about 2k for all of it to be done.

c) Maybe don't spend it on the car, but if I don't, what? Buying a house just won't be happening at the moment (but regardless of what I do, my promotion I'm looking at in the next 6 months or so would mean I would then be able to look at doing that with another person or two) Don't really have much apart from the car so ideas are limited!

That is all :(

Link to comment
https://www.sau.com.au/forums/topic/204089-tell-me-what-i-should-do-next/
Share on other sites
Woodys Community Regular

Woodys

Posted
Posted (edited)

Well if you`re happy with the power you got at the moment then i would either use the kit you have or sell it since its only sitting there gathering dust.

Not sure on what you got in comfort wise as in the seats, perhaps look at a seat upgrade and maybe some upgrade to the rear seats.

Or even a suspension upgrade if you haven`t already done so.

Stock car look can be less attraction to the police at times and also fun when that V8 rocks up beside you wanting to give you a run and you leave him with that stunned look on his face eating your dust.

Anyway just my 2 cents worth.

Good luck on what ever you decide on.

Edited by Woodys
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Import insurance in 2025

      By Kinkstaah · Posted

      The max they would go for me is 50.
    • Duncan
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By Duncan · Posted

      That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

    • GTSBoy
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By GTSBoy · Posted

      I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Got started on the modification to make these splash plates fit over the long weekend. First the surprisingly time consuming task of swapping all the cam cap bolts to Tomei cam cap studs. I did the method of removing one bolt at a time, applying loctite to the stud, double nutting to torque as the manual described. Then carefully unlocking the nuts without disrupting the torque of the stud (and going back to re-torque a few times when it slipped). Finally applying the nut and torquing to spec. Repeat x28 Next up I went about removing the stock cam cover baffle so I could ensure it was fully clean after drilling for stud clearance.  As the blind rivets holding the baffle on were domed I used a punch to mark the center then used 4mm drill bit to carefully drill out the rivet without going too far part the baffle. As seen in other thread here is what is inside the stock baffles I decided on M4x6mm bolts to bolt the baffle plate back on with. I used a 3.3mm drill bit with some tape to mark the depth at ~8mm. Next was to tap the threads using a cheap bunnings kit M4x0.7. With the baffle removed I also drilled out the spot welds holding in the baffle plate oil returns. Unsure whether this was the best option or if I should have cut holes in the Hypertune splash plates to allow the oil drains to still function... time will tell. I then removed the the Hypertune splash plates so I could rest the cam cover on top and use a dab of grease to mark where the studs impacted the oem cam cover baffle. The most obvious spot was on the hump from the stock mesh is held. Using this hole as an anchor I bolted the oem baffle plate back into the cam cover and lined up the Hypertune splash plate. Marked the rest of the holes for the studs and drill those out too. Total 32 holes drilled and 12 threads tapped on the passenger side cam cover alone for this bolt on part that totally clears all OEM cam covers.. Drivers side next as well as some E85 safe fuel foam to fill the space behind the behind cam cover baffle plates. oh and some lock nuts for the splash plates of course.
×
×
  • Create New...