Jump to content
SAU Community

Recommended Posts

Anyone spot this recently?? Its been in storage for 5 years but sold this week..

Hope its taken care of :)

post-5116-1257039836_thumb.jpg

Holy turn back the clock Batman - haven't seen her for a VERY long time! How is Tokyo treating you N/A?

spotted the 34 with the night kids sticker down on moana beach this arvo

and spotted me earning a 6 pack, a stubbie and a bottle of wine for 2 recovery efforts. 6 pack for the Mecair van and the stubbie and bottle of wine for doing a 2 snatch pull on a mitsubishi rosa bus (converted to campervan)

Spotted yesterday a red r33 with a huge wing for sale at Semaphore, also spotted around 7.30pm a white s2 33 female driver and a white r34 with CC plates driving behind me along Semaphore, nice rides.

Edited by kb-r33

spotted luke and damo's 34s, and also chads 32 and rubys stag representing at EHP :D looking good guys!

Also spotted luke again down the bay around 7, exchanged waves...then also got a wave from a guy in a red s14 s2.

Saw many other skylines parked down at glenelg, too many to remember.

Tokyo is fine Nightcrawler and although I miss Aus at times, I dont miss the police and the defects.

Just sold the old girl to a pretty good guy in Adelaide so you guys might see her around. Think he might change the wheels to some black Welds though..

spotted luke and damo's 34s, and also chads 32 and rubys stag representing at EHP :D looking good guys!

Also spotted luke again down the bay around 7, exchanged waves...then also got a wave from a guy in a red s14 s2.

Saw many other skylines parked down at glenelg, too many to remember.

thatd be dave (scandyflick)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...