Jump to content
SAU Community

Recommended Posts

hey guys,

bought a brand new xforce highflow cat off Ryan1600 and put it on the car tonight.

With the new cat on, even with the gaskets, in the middle of the ovals on either side that join to the next part of the exhaust ( the part furthest away from the bolts) I can put my hand under there and feel some of the warm exhaust gases blowing out in the crack.

Just to make it clear... so if the top and bottem of this oval are where the bolts are, the part that I can feel gases is ... ---> () <---

Is this acceptable or does it have to be completly sealed? and if so, wot is the best way?

And I tightened the bolts up hard enough to squish the bit of the gasket around them, but not in the middle.

1 other thing, my old gaskets appeared to be larger then the ones that came with the xforce... should those maybe go back on?

appreciate the help :)

Adam

Link to comment
https://www.sau.com.au/forums/topic/205808-question-about-exhausts-and-joins/
Share on other sites

The flange on the existing pipes has probably warped a bit. You can get special high temperature sealant (like putty) that you can coat the gasket with. That should help create a proper seal at the flange joints.

Thanks guys, appreciate the help.

Can I drive the car around for the day as it is?

is it possible for me to put two gaskets on? ie, the old + new one? or is that a bad idea? because by the looks of the old 1, with that combined with the new 1 it should be a good fit.

just use that exhaust gasket goo stuff. it's only about $10 a tube. put it on the flanges and use a gasket as you did, and hopefully it will seal. if it doesnt, you'll need to find which face is warped and get it machined flat. well not even really machined.... you could prob do it yourself with a grinder and a steady hand.

Edited by Munkyb0y

I will go out and get a tube of that stuff ( sounds like it could come in handy) but I just chucked on the old and the new gaskets together and it now appears to be fine :) I may still put some stuff on it just to be safe.

Thanks for the help guys ;)

You'd be better off with two gaskets. Goo will take weeks to get it hard enough to be heat resistant. Usually melts or burns out - and its messy

If you machined it flat you shouldnt even need a gasket as the materials are the same and will be running at the same temp

If you pull it off yourself it would cost less than the goo to machine

The stuff u need to buy is CRC Maniseal Exhaust Cement!

u use this stuff on both sides of exhaust gaskets and as the first time the pipes get some heat in them this stuff will set and stop all those unwanted leaks!

you can purchase it from any auto place eg. repco, bursons, supercheat, etc

Appreciate the help guys.

You know, I gave the car a bit of a flog today, only for a couple of minutes, now I don't know if I have started to become used to the slight lack of power or if the power has gotten back up to what it was somehow.

you know that sensor that plugs into the cat? wot does that do? does it tell the car how much approprate flow it should have? I don't know, it just seemed to have a good strong burble session down this hill, then after that the power didn't seem to be as laggy and it feels abit more torquier from then on.

is this possible?

the other thing I am curious about. these cats flow at 570cfm or some unit of measurement. how much flow does a straight 3" pipe provide?

Adam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just planning to have the wiring neat and hide as much as possible.
    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
    • You can probably scrub the rust with a toothbrush or something. After you get the rust off flush well with water to neutralize and you will probably want to also use a fuel tank sealer to keep it from rusting again.
    • The sodium citrate solution is designed to buffer the citric acid to keep it from attacking metal quite so much, the guy that came up with that recipe did a ton of testing on how much metal loss occurs over time and it's nothing crazy unless you forget about it for months:   
×
×
  • Create New...