Jump to content
SAU Community

Will These Splits Fit My Car? And Which Of These Head Units Will Be The Better Option For My Setup


Recommended Posts

Hi all

I'm in the process of working out my car audio setup for my 4 Door R34 and am a bit stuck on which front speakers to buy, and also which Head Unit to get installed.

Speakers first:

At the moment the decision is between JL Audio VR600CSI Splits, or the new Alpine Type R Splits.

They will be running of a 4x60wrms Pioneer Amplifier (GM6300F). If I go the Type R splits, I will probably bridge the amp to feed them the juice and focus on the front staging as I am going for a sound quality focused install rather than just what's loud and clear.

Now the question is, will these Type R components fit in the 4 Door R34? Has anyone had any experience with these speakers and skylines?

The salesperson had concerns about the depth of the Type R speakers but said that there wouldn't be any problems with the JLs. However looking at paper specs the surface mount depth of the two speakers are the same?

I would prefer the Alpine speakers and they're also going to cost a fair amount less at the moment which means I can put the money I save towards getting my doors skinned with deadener.

As for the head unit:

I was looking at a JVC KD-AVX11 to get the in between of DVD and a good deck with 7 band Equaliser. Then I discovered that they only had one set of preouts so I disregarded that head unit.

After hearing a 3preout JVC DVD Source unit and then an Alpine equivalent, JVC is now out of the question!

So I've narrowed decision down to the following non-dvd units to focus on sound quality at an affordable price as that's what counts when you're driving and aren't watching the screen:

Pioneer DEH-P6950

Alpine CDA9885

As far as aesthetics and menu layouts etc.. go, I am leaning towards the pioneer, though I believe the Alpine to be marginally better in the sound quality. Note that the Pioneer unit has 7 band equaliser.

Any experience, suggestions, advice on which way I should perhaps go with my head unit suggestion will be taken into consideration. Both are the same price. I'm looking at all aspects from sound quality, to build quality and functions features and what's going to be easier to live with using everyday.

Thanks in advance :blush:

Edit: Figure that a bit of a run-down of the rest of the system will be helpful

Most of the components I already have from my previous car so they will be used..at least for now:

GM5100T 2x125WRMS Bridgable

GM6300F 4x60WRMS (will be used to power the speakers)

Lightning Audio Strike 15" Single Coil in 1.5Cu.Ft.

4Gauge Schneider OFC

Gold 4Guage in 2x 8Gauge out Fused Distribution Block

2x Sony RCA Signal Leads

1x Jaycar RCA Signal Leads

I would like to replace the 15" sub with 2x12" woofers as I listen to all types of music and for some certain Genres I prefer to have an in between of tight bass and low deep bass..but that may come later, I'll just use what I have for now.

Edited by N-DAWG
  • 1 month later...

hey!

as far as the headunits go, ive got an alpine CDA 9885i and its sweeeet, plays so well, its never skipped and ive had sum reall scratched cd's in it. features r u can change the colour of ur main opperation buttons between red and blue, u can controll ipod from headunit not from ipod, i think its the same with bluetooth, havnt set that up yet, can have background visuals while lsitenin 2 music, comes up wit notes sayin happy new year, xmas, u can even set ya b-day in it fo it 2 say happy b-day lol as for speakers ive got S type 6.5inch speakers front and back aswell as a 12inch S type sub all amped from a 1200 watt amp and thats loud enought rearview mirror vibrates like hell and cant c out of it when on max vol lol :banana: no distortion on front and rear speakers from 2 much bass, crisp & clear music, my girlfriend says she can hear it from her room at the back of the house and can hear word for word, das how clear it is. if S types sound really gewd id think R types or even X types would b crazy! :D

Alpine 9887 ftw!

R-types are good(I've got splits up front, coax up back), but I think you'll need a spacer for the 6.5' speakers, the r-types actually come with some, but I can't remember if they were enough to clear the frame or not, mainly because I already had mdf spacers in there.

hmm i wouldnt bother bridging the 4ch down to 2 channels to run the fronts. At the end of the day you will be running it through a high pass filter in your SQ install to keep thclraity up, which means that they do not need a huge amount of power. You would do better to run a speaker off each channel ie amp your rears as well, thus giving you an even sound from front and read, as opposedto just a massively overpowered front stage.

pretty sure that ur pioneer 2xh is going to underpower that sub, too. For SQ, you want to have an amp that puts out a highr RS than your sub, then only run it at 1/2 to 2/3 gain so that it isnt maxing out. You get better sound when your components arent at their limits. Plus, a 15 in the boot of a car isnt the best for SQ. They take a bit of power to deliver the punch you need.

Type R Fit just but with spacers... and sound like shit, trust me I tried it.... DD liner sound much better. but if you can stay away from /////ALPINE the better.

Edited by Hotr34

Hey guys

Thanks for the replies.

I ended up getting the bits mid/late Feb and just remembered I'd posted this thread :D

Some great replies there too.

I had to lower my budget a bit due to unexpected expenses that managed to pop up but I think i still managed to do well considering how much I saved on the bits I bought.

I ended up buying the Kenwood X8006U Head Unit, saved about $300. It covers the iPod control without purchasing any additional cables etc, has 3pairs of 5volt, covers the tuning aspects that I wanted and leaves me with room for expansion later on.

I installed NV Splits up front and powerplant 2-ways in the rear shelf..the price was right for these parts and they don't sound too bad considering. And yes I had sound deadening fitted for the front speakers, though I'm considering doing the door skins as well later on.

For reference, the NV Splits just fit. The installer had to cut into the plastic on the factory speaker mount to fit the depth, but I was told it just cleared.

I was nearly going to get a pair of Orion splits (ex display models) which would have set me back around $400 a pair, though the saving was quite huge. I can't remember the model of these but they were almost like a miniature sub in design.

As for the 15" sub...I would really like to sell it and buy a pair of 12" woofers (undecided which ones at this stage) and I may even do a custom enclosure to make the most of the R34 boot space. For now I'll just keep the sub though until such time as I'm ready to upgrade it...besides I'm saving towards getting exhaust work done at the moment so the sound system will be fine for now :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi Rob It's a nistune ecu. Yes same shop, good reputation. Apparently the computer on the dyno is compensated for temperature.    Chris was saying that the lean or richness of the mixture would be covered in the actual tune, but he's already picking up in advance that it's under what it should be. Regards the dyno, it's also noticeable on the road. But I just want to add something that has just come in, it appears there might be something in the setup of the external wastegate. In the exhaust manifold there is a centre divider between the front three and rear three cylinders. The external wastegate has a pipe from each side that join at the wastegate. Theory is those two pipes just might be pypassing that divider and introducing a problem somehow. Is anyone familiar with the divider in the exhaust manifold and the effects if the two wastegate pipes were to create a bypass path? Thanks for your questions Rob, interested in your thoughts on this external wastegate bypass theory. Regards Rob
    • Meh, At 60 years old, I have been doing dumb stuff for much longer than you mate, I am the true King And unfortunately I cannot be a maroon, as I am not brownish red As for not getting ITB's, the plenum intake will apparently show typical gains across the board and increase induction noise a bit, but, have all over less dort than ITB's Cost difference for the extra ITB dorts was significant though, the total parts for the plenum set up is "around" $2kAUD plus shipping, the ITB's were $4kAUD plus shipping, I was contemplating really hard about paying the extra $2k for all of the dorts, but weirdly, some form of common sense, from listening to the platform experts prevailed  As for the NA mod hate by some, I've had a few boosted cars, with all their inherent issues, I'm now looking at simplicity and legalities for a street car, maybe I'm just getting old, and I'm quite happy to spend some of the kids inheritance, 5kw at a time 🤣 And think of all the money I'll be saving on consumables that something with boost needs, like engines, gearboxes, diffs, clutches,  tilt trays... etc. etc. etc. 🤪
    • Haha.  I wouldn't say I am either but I've definitely been around it plenty.  I'm guessing you know the dial in is basically to make a handicap to level the playing field between racers.  The car with the slower dial in goes first and in theory if they run their dial in time and the faster car also does then they cross the finish time if they also have exactly the same reaction time - if you go faster than the dial in them you lose, but if you are too slow there's a good chance the other person will get to the finish line first. I'm normally supporting other cars but they were all pretty dialled and were egging me on to race as well, here's one of the cars I tune (Starlet) which ran within like 1 hundredth of its dial in through the competition: https://www.youtube.com/watch?v=inEBu-d9Gn4&t=69s
    • Where ever the fuel reg gets it reference is what I use to T into for map reference been a very long time so where it goes to plenum/runners I have no idea but never had issues. 
    • What ecu? Same shop every time? Same ambient temperature? If timing is correct then pull plugs and see if lean or rich. Dyno can also read different if they have changed ramp rate or not set tacho/speed properly  
×
×
  • Create New...