Jump to content
SAU Community

Recommended Posts

Guest thrat

Just bought a r32 gtr which is completely stock off one of my mates.I would like to get some good performance out of it.My goal is to build a reliable low 11second beast for the street and also for the once a month street meets at AIR.I am not very mechanically minded but of got plenty of dough to spend on it, I think.I have a budget of 20g's to work with. Will I beable to reach my goal with this figure??Anybody have any tips of how to go about it??Things to watch out for??Any help would be great...;)

Link to comment
https://www.sau.com.au/forums/topic/20639-gtr-performance/
Share on other sites

Should be able to reach 11s quite easily, as I read a post somewhere here where a guy with stock turbos, more boost, exhaust, air filter, cams...etc - no major internal work, achieved around 250kW@wheels and ran high 11s. To go more than that you would need upgraded internals, larger cams, larger turbo or turbos, fuel, ECU...etc. It gets to a stage where to go a little bit faster, you have to spend a LOT more money!! Once you start getting into an aftermarket turbo, ECU...etc it gets expensive. Also depends what branded parts you want to use. If you go for big names like HKS or TRUST, a new turbo kit for the GTR will cost well over $10k. Or you can buy other cheaper brands, or second hand items. If you ever want to change the gearbox, I have heard that it's d@mn expensive, like $15k for a TRUST 6 speed or Holinger shift...whatever it is ;) The GTR gearbox will need to be replaced if you want to run 10s. For 11s, the standard one should be ok.

Link to comment
https://www.sau.com.au/forums/topic/20639-gtr-performance/#findComment-432530
Share on other sites

cold air filters

Z32 AFM's

good exhaust

front mount? (maybe)

hi-flow turbos

power fc and boost controller

some nice suspension

a good clutch

fuel injectors, regulator & pump

good performance tuner

other misc bits n pieces like oil/air sep., cam gears, replace all belts, fluids, plugs, brake pads etc. with good stuff.

15 - 20grand for the above i rekon (realistically). should run 11's, i dont know, i dont own a gt-r or know anyone who has modded one.

:P

Link to comment
https://www.sau.com.au/forums/topic/20639-gtr-performance/#findComment-432754
Share on other sites

thrat,

I've got HKS 2530's and dumps, HKS FMIC, Power FC, full exhaust, twin plate clutch and have 340hp at all 4 wheels (253kw) on 1.1 bar. Haven't taken it down the 1/4 yet as new 700cc injectors and cam gears are going in very soon.

I know you can get those turbos for less than $5 brand new, and I got mine second hand for less than $3.5k and they where in perfect condition. One thing I would recommend is changing the standard cooler as soon as you upgrade the turbos. Everyone tells you that they are good for 450 odd hp but I changed mine and picked up over 40hp at all 4 wheels right across the rev range at around 380hp at the fly.

Getting into 11's isn't as easy as a lot of people think, apart from hp you need to think about other things like clutches, diffs, drive shafts etc. Remember an R32 is at least 9 years old now so things like that might be starting to get a bit worn.

I know people who have run as much as 550hp at the fly through a stock bottom end RB26 for over 18 months without problems.

Good luck with it, it costs a bit but is lots of fun.

Brett

Link to comment
https://www.sau.com.au/forums/topic/20639-gtr-performance/#findComment-433671
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...