Jump to content
SAU Community

Recommended Posts

Used DBA5000 2 piece slotted rotors 324x30mm to suit Front GTR Brembos - better than the DBA4000. New they are about $1000. You can replace the disc part (reusing the hat) for about 400-500. Discs are probably about half worn. *SOLD*

Brand new, still in box Ferodo DS3000 pads to suit front GTR Brembos. *SOLD*

2 sets of used Ferodo DS3000 pads, to suit front GTR Brembos about 50% left on each set. *SOLD*

1 set of Titanium shims to suit front GTR Brembos. These block the heat getting into your caliper/fluid. *SOLD*

hey Ferni I need some rotors, was about to buy some RDA slotted but I reckon these are a better option... will they get me through a couple of track days before they need replacing? who does the replacement disks for them?

Yeah they will last ages still... Much better than RDA in my opinion.

DBA will do the replacement discs for them... through anyone who sells DBA discs... Brake places, Repco, Bursons etc..

Give me a call Nick.. i'll pm you my number.

Naaa for a set of 2 discs... about 200-250 each disc i think... that's when i priced them when i bought them last year.

Call burons and ask for a price on DBA5000 replacement discs (Without hats) for GTR brembo rotors (324mmx30mm).... You'll get a better price if you can get trade on it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...