Jump to content
SAU Community

Recommended Posts

well i got RB74 front pads, and they squealed when no brake was applied, when applied it is quite normal for them to squeak. So i got my discs machined cos they were warped and had a lip, wow it worked! no more squeal. BUT i was at the track today, and after the day they now squeak again and very annoying! The discs i think are too thin to be machined again, wat do you reccommend ? new discs ? or could it be some thing else like dirt stuck between pad and rotor? :P please help me

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/
Share on other sites

Maybe the pistons arent retracting all the way, my car had the same drama, you could always hear the pads rubbing on the rotors.

It wasnt until you pressed the pedal and the pad was in full contact witht the rotor that the noise went away.

Had the calipers re-built, now they are as good as new.

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-434555
Share on other sites

When you machined the discs did you sand back the pads as well? Both pads and discs will become glazed over time, and if you scrub one back without the other, the one you scrubbed back will just get glazed again really quickly and you'll be back to where you started.

Could be the discs are too thin too, things will glaze up easier if there's a lot of heat involved. I think new DBA4000 discs are around $200 each. It may seem expensive, but they are probably a lot cheaper and definitely a lot better than the OEM items.

If you are really pushed for cash, maybe try buying someone's second hand discs? If you do, make sure you check for run-out. The factory items are 30mm thick when new, and need to be replaced at 28mm.

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-448548
Share on other sites

Its not cheap, and you cant be sure that calipers need rebuilding until they are apart, then its too late as most of the expense has already been incurred.

If you need new rotors then that is the logical place to start. People laugh at the lengths i go to, to make sure my brakes are properly cooled down after each run at the track.

Its all you can really do to stop them from warping/cracking, that and not using the handbrake when you park it after a run.

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-448558
Share on other sites

the pads were brand new when i got the discs machined, they hadnt been bedded in yet. The machining took the squeal away after the track day they started to squeak again. The calipers are fine, dont need a rebuild, its most likely the discs are quite thin so theres still abit of warp in them. I will live with it for now as its on and off thing (hard metalic pads create squeaks) im looking to upgrade to GTS-T brakes in the future without a stud conversion, the calipers can bolt straight on, they are just fatter and i might need new wheels :D Thnkas for the help ppls, Ben i dont think i will buy them, thanks neways im not sure if the GTS-T discs are much bigger? as the pads are the same size

Roy- i always drive around the track again using no brake to cool them down and i dont use the handbrake to park either, but its only the fronts which squeak, id say its the thin discs and new pads. with the standard pads i used them twice on the track and they were gone, ive used the race brakes once and they havent even lost a mm and that was real hard braking

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-450596
Share on other sites

Originally posted by Roy

I love track days, it would be good if someone else would pay for the servicing on our cars:D  

Sounds like you have it sorted, happy motoring.

You can get someone else to service the car you are driving by borrowing someone else's!

/cough

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-451053
Share on other sites

My recommendation is slotted rotors too, since I have fitted them to my car, not only do I get a lot loss fade on the track, but no squeak either...more a low pitched groan under heavy braking as the rotor chops up the pads.

DBA's are good and reasonably priced, check their website

www.dba.com.au

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-451213
Share on other sites

You can get someone else to service the car you are driving by borrowing someone else's!  

/cough

Oops, let me clarify myself, my car is the designated T-car, yours is the race car. Your the team manager, and im the backward a55 driver.:P

Hey, and i dont rev yours over 4,500 - 5,000rpm, you have seen how i drive my car when i get excited. Me in my car = Drive:mad:

Actually, i think i should just say thanks for the drives, and think of ways to thank you, need your car detailed?:P

As for Comp 15 pads, PM Silver-Arrowz, i think he uses them, may have been Comp 9s and whatever he is using is hard on rotors.

Link to comment
https://www.sau.com.au/forums/topic/20662-rb74/#findComment-453241
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Only reason to keep a MAF on your RB25 is to be able to easily calculate true VE if you know what the factory voltage curve represents in grams per second of flow. Also allows you to do things like pull the original OEM ignition + AFR target tables and use those as a starting point for your base map. Once you're well and truly done tuning though there's no need to retain the MAF.
    • Do you think they'll merge there performance divisions and we'll end up HoMo?
    • Very true, if buying new, I would not get an PP either. Minimum is an Elite 2500, which is also considered outdated. Get something that supports DBW, delete that cable throttle. Best thing I've ever done to the Skyline, next best is refreshing the A/C with a new condenser. It's cold, but not as cold as modern car, but colder than most 90s JDM shit boxes imported into Australia.
    • Haltech have a nice comparison table between the Elite and Nexus models -  https://www.haltech.com/ecu-buyers-guide/ In general, the Nexus is better. Haltech have some nice product videos on their YouTube page, I'd have a look at those and if you're still not confident what way to go, I'd give them a call. They have the best customer support of any company I've dealt with, I'm sure they'll be able to help you out. 
    • Not to mention, that the correct diagnostic approach to "electrical thing does not work" is to start with what I outlined above. You only do swaptronics for things that can't be tested really easily, like ignition coils, AFMs, etc etc. And even then you hold your breath in case the fault that possibly killed the original unit kills the swapped in unit too.
×
×
  • Create New...