Jump to content
SAU Community

Recommended Posts

if it dosent sell in a week it will go to auction. Wreckers are asking $2000 for a very clean complete rear cut.( GTST)

Hi everyone I am selling my damaged 1995 r33 skyline Gtst .

Im being straight forward so read CAREFULLY. this was a very clean car.

Ok the car had 71xxx kms on it. What you see is what get. Everything has been photographed take a look. HEAPS OF PARTS, probably not worth repairing but good to use for fixing at least 2 cars and selling the rest.

The car is a reparable write off in Melbourne but has a clear title in Sydney(no revs) so can be registered

The car has heavy structural damage to the near side(passenger side) chassis rail, As a result the strut tower has collapsed into the fire wall damaging it. The near side front suspension is all damaged. There is also a lager kink 1/4 the way through the passenger door sill. The front of the roof is also damaged as a result of this kink. The radiator support is also damaged. Bonnet has minor damage.The front drivers side rail at the front remains undamaged.

The following is missing of the car.

The complete motor gearbox and tail shaft

The brake calipers

Seats, that's all I can remember but what you see in the photos is what you get.

What you get (as the photos)

The car has a complete rear end (quarters never damaged before, and nice wing) with diff and cradle. The complete off side (driver's side) is also NOT damaged and very straight. The passenger side door has a slight ding in it.

The car comes with.

doors

off side gaurd

off side front suspension

Near new front rotors

Rear rotors

Hand brake

Complete sun roof(with roof liner not damaged)

Complete steering column with key and steering wheel(car has keys)

Dash / dash surround complete

All interior plastics and seat belts

Ac climate control switches

Fan shroud and slightly damaged radiator

All fuses and wiring including ECU

Brake booster

3 stock wheels

Air flow meter

grill 400r

And everything you see in the photos.

$2500ono. serious offers considered Allen 0424333012 of PM with a figure. FREE TOWING TO SYDNEY METRO areas.

SHE NEEDS TO GO ASAP

Towing to Melbourne or Brisbane is $350 door to door.

post-46494-1203653104_thumb.jpg

post-46494-1203653126_thumb.jpg

post-46494-1203653141_thumb.jpg

post-46494-1203653162_thumb.jpg

post-46494-1203653178_thumb.jpg

post-46494-1203653194_thumb.jpg

post-46494-1203653229_thumb.jpg

post-46494-1203653247_thumb.jpg

post-46494-1203653264_thumb.jpg

post-46494-1203653289_thumb.jpg

post-46494-1203653307_thumb.jpg

post-46494-1203653323_thumb.jpg

post-46494-1203653345_thumb.jpg

post-46494-1203653362_thumb.jpg

post-46494-1203653383_thumb.jpg

post-46494-1203653398_thumb.jpg

post-46494-1203653414_thumb.jpg

post-46494-1203653430_thumb.jpg

post-46494-1203653466_thumb.jpg

Edited by Xr33
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...