Jump to content
SAU Community

Recommended Posts

mine also seems to start slow but at the moment, has gone flat!? i have an apexi full auto timer which has my battery reading at 10.4 which is way low!

I have put another alternator on the car i was thinking this may be the problem?

SHould i have my battery charged/buy a new one?

What else could it be?

Link to comment
https://www.sau.com.au/forums/topic/207255-slow-starter/#findComment-3667141
Share on other sites

alright im not sure if it is a problem because it does start every time, but it always take about 2-4 seconds before it fires up. Is this normal and how can i fix it?

Does it sound like the starter is struggling to turn it over? If so I would check the battery voltage and if it seems low take it to battery world or something and have it tested.

mine also seems to start slow but at the moment, has gone flat!? i have an apexi full auto timer which has my battery reading at 10.4 which is way low!

I have put another alternator on the car i was thinking this may be the problem?

SHould i have my battery charged/buy a new one?

What else could it be?

I had a problem with my battery going flat and found out the stereo was causing it... drawing current all the time. You can test to see if your battery is being drained while the car's off by disconnecting the negative battery terminal, and putting your multimeter in series to check how much current is coming out.

Don't switch the ignition to any sort of "on" while it's connected like this, or you'll likely kill your multimeter and melt some wires in the process.

Make sure all doors are shut (boot included - you'll need long leads to get to your multimeter through the gap in the boot), and then wait for the light around the ignition key hole to turn off after closing all doors. If the current reads in the hundreds of milliamps then it's worth pursuing this further.

I don't know much about alternators, though I've read that a healthy alternator should put out 14.4V or more (prolly need to rev engine and look at the reading).

Link to comment
https://www.sau.com.au/forums/topic/207255-slow-starter/#findComment-3667484
Share on other sites

Does it sound like the starter is struggling to turn it over? If so I would check the battery voltage and if it seems low take it to battery world or something and have it tested.

I had a problem with my battery going flat and found out the stereo was causing it... drawing current all the time. You can test to see if your battery is being drained while the car's off by disconnecting the negative battery terminal, and putting your multimeter in series to check how much current is coming out.

Don't switch the ignition to any sort of "on" while it's connected like this, or you'll likely kill your multimeter and melt some wires in the process.

Make sure all doors are shut (boot included - you'll need long leads to get to your multimeter through the gap in the boot), and then wait for the light around the ignition key hole to turn off after closing all doors. If the current reads in the hundreds of milliamps then it's worth pursuing this further.

I don't know much about alternators, though I've read that a healthy alternator should put out 14.4V or more (prolly need to rev engine and look at the reading).

Yeah cheers man, i have an old atlernator hre (it squeels a bit, think bearings are gone) however it did work..so i'll bolt that on today and if that doesn't work i'll try charge the battery again. (Who can do that for me?) if that is no good it either is drained from a source or it is time for a new battery.

Link to comment
https://www.sau.com.au/forums/topic/207255-slow-starter/#findComment-3668286
Share on other sites

dw guys, i just finised bolting on the original squeely alternator, kick started in 2nd gear and she is now charged back to 13.9voltz which is great! and the old alternator is not squeeling!!! well for now anyhow..

Link to comment
https://www.sau.com.au/forums/topic/207255-slow-starter/#findComment-3668519
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea the photos aren't the best. When I was pulling the bumper and headlights out there was a bodyshop guy looking on for it, there is a slight bend behind where the passenger headlight is, but we're talking a few MM and there is a little bit of a bend for the reo. That said it's supposedly well within the "Drill a hole in it and pull it out with a slide hammer to be close enough" and be on our way. The other option is to buy a GTR reo for the GTR bumper bits but this is a $2000+ fix for something Mr Hammer can probably do 99% of the job for and everything will/can line up pretty closely-to-good-enough.
    • That's a write off for sure... Part out? 😛 I kid. It looks like the rad support has a minor minor bend in it too where the rep support sits near. Could just be the photos (and me not wearing my glasses right now). Worst case is you can buy a new radiator support, have it swapped over, and leave the car in paint jail for 12 to 18 months while you build the motor to handle twin turbos or a Harrop SC...
    • It seems the definition of "Gregging" something might need to be expanded?
    • This is why I suggested that there is really nothing that can safely be done in the engine bay at this budget level. Just the work to reassure yourself that the engine won't instantly crap itself the moment the boost gets turned up will wear out the piggy bank long before the first turbo gets installed. Spend $10k and still not have any extra performance? My tip is a version of our standard advice from 15 years ago about buying a GTR, which is not to buy one unless you can afford to buy two. The new version is not to modify a GTR unless you have all the funds required to do it all at once, properly, and enough to rebuild it after it blows up.
    • Oh, I forgot to mention this before.  It is accepted that your taking on risk buy turning up the power on a 30 year old stock motor. You can lower the risk with the ECU engine protection, but this is more money on sensors. CAN wideband, oil temp, oil pressure, coolant pressure, fuel pressure, air temp, etc. It adds up quick.  I am a huge fan of running all of the engine protection the ECU offers. You'll have to decide for yourself how you want the engine protection setup and what you think is worth monitoring. 
×
×
  • Create New...