Jump to content
SAU Community

Rb25det Afm S1 And 2

kurd_boi

By kurd_boi,
in Engines & Forced Induction

 Share

Recommended Posts

TTT Grand Master

TTT

Posted
Posted

because most R33's with RB25 engines are running near max voltage after 200rwkw.

at 220 that you want, they will be past their resolution.

and series 1 to series 2 AFM are slightly different. but still max out at the same level.

you are changing the afm. might as well start with the right one instead of having to change it again in the future.

dezz Grand Master

dezz

Posted
Posted
because most R33's with RB25 engines are running near max voltage after 200rwkw.

at 220 that you want, they will be past their resolution.

and series 1 to series 2 AFM are slightly different. but still max out at the same level.

you are changing the afm. might as well start with the right one instead of having to change it again in the future.

my car is making ~250rwkw on the stock afm :(

  • 3 weeks later...
TTT Grand Master

TTT

Posted
Posted
my car is making ~250rwkw on the stock afm :(

that's why I said most.

and did you tune it?

did you see it being tuned?

do you have a PFC hand controller where you can see the AFM voltage?

is it not hitting max (4.8 or whatever it is) way before redline?

You can tune the car still once it has passed max voltage..

but it's not as accurate.

which kinda defeats the purpose of having an AFM equipt car..

and it is kinda in the zone where you would want to place the most emphasis on getting the tune right.

  • 3 weeks later...
  • 3 weeks later...
James_03 Mentor

James_03

Posted
Posted (edited)
from wat i have read on here the R33 s2 pins , 2 of then are for grounding ! can anyone comfirm !

No thats not correct.

The S2 pink label R33 AFM has 3 terminals. With the AFM facing towards you and the flow arrow pointing ===> they are:

pin 1: 12v from eccs relay

pin 2: Ground

pin 3: Signal

The Green label R33 S1 AFM however uses 2 grounds. The first is an ECU ground, the second is a Chassis ground. This is the same scope and dimensions as a rb20det silvertop AFM, the terminal outputs are slightly different but both 80mm.

Here is something a found on the net ages ago that I dig up when I need it:

post-13028-1208908227_thumb.jpg

Edited by James_03

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...