Jump to content
SAU Community

Fs: Cheap Rb25det Bits Swsyd

gt-ahhh!
 Share

Recommended Posts

gt-ahhh! Proficient

gt-ahhh!

Posted
Posted (edited)

LOCATED SOUTH WEST SYDNEY (picton) can ship at buyers expense, or organise pick up or drop off to campbelltown-liverpool-southern highlands area within reason.

Item: standard coilpacks / coil packs

Age: as above i expect

Condition: good, working fine

Price: $80

To Fit: RB25s, maybe others

Comments: as is, w/o leads

post-40626-1204525661_thumb.jpg

Item: stock exhaust manifold

Age: as above

Condition: good

Price: $30

To Fit: (What car) RB25s, maybe others

post-40626-1204525768_thumb.jpg

Item: stock turbo dump pipe $30

Item: water pump $20

Item: stock R33 fuel rail with injectors + plenum SOLD

Item: crank angle sensor SOLD

Item: alternator SOLD

Item: valley cover SOLD

Item: reconditioned RB25det head SOLD

Item: sump SOLD

Item: ignitor SOLD

Item: hks actuator SOLD

Item: cam cover SOLD

all prices ono, within reason.

i still have a lot of other stuff, covers, heatshields, bolts, nuts etc. feel free to ask

contact: PM preferred, or comment here. i check very regularly and will reply quickly. any queries/comments/more pics, no probs.

have good trader rating too!

thanks lads!

mitch

Edited by gt-ahhh!
Link to comment
https://www.sau.com.au/forums/topic/208751-fs-cheap-rb25det-bits-swsyd/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...