Jump to content
SAU Community

New product to avoid speed cameras

Torrens

By Torrens,
in General Automotive Discussion

 Share

Recommended Posts

MattyB Community Regular

MattyB

Posted
Posted

with that product do take into account that its designed for different shape licence plates. so the spring tention could be too little.

for rear licence plates ive looked at setting up a air ram or electric solinoid valve for moving that up n down. once ive finished this ill post more. (that could be years knowing me)

Ben Explorer

Ben

Posted
Posted

My boss told me that you can transmit a certain AM radio frequency that renders a RADAR speed camera (not 3 lines on road) ineffective whilst in range of it. Just a matter of trying it out some how. Older speed cameras that use the 3 lines on the road are not succeptible to such trickery unfortunately.

This technique also works with Porches, by transmitting AM frequencys when your next to a Porche it will shut down its ECU and the driver will have to start the car again. Very effective for drags.

That spray looks pretty good, I had an idea once of putting a high output xenon globe above the number plate that was triggered off by a flash sensitive device...... hopefully in time to blind the camera.

Alternatively you could use solenoids to flip your number plates up and down using a switch inside the car.

So many ideas....... mwaahahahaha ;)

akeenan Grand Master

akeenan

Posted
Posted
akeenan if you do a good ennuff job of the flippers etc etc then its really going to *** with his head.  

most likely get a sticker, but if the plates couldnt be moved when he tried to move then he would be left really confused.

except for the common fact that police browse these forums and are now aware of these devices i think youd be in a bit of trouble.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 GTST - 600KW+ RB28/CD009 Build

      By GTSBoy · Posted

      Unless things that you want to do include reference to time. Simple Boolean logic is only good for digital inputs or analogues that have been thresholded into digitals. But unless you also have a timer function available (which would more ideally be located inside the program, rather than being forced to implement a timer outside the ECU and bring it in as a seperate digital for every time delay you want to implement), then you can't do some of the things that you might want to do. My PLC ladder logics are obviously littered with program blocks, because that's easier than building it all in ladder gates, but the most frequent of those program blocks is a simple timer, because you actually can't otherwise do that in ladder at all.
    • GTSBoy
      Low oil pressure after WOT

      By GTSBoy · Posted

      Log voltage. I'm suspecting the alternator. Or even maybe a bad earth somewhere. ie, seeing as it is rev dependent, I am thinking it is alternator dependent.
    • Duncan
      Low oil pressure after WOT

      By Duncan · Posted

      Yeah so N1 and any other larger than factory pump are pretty famous for pumping the sump dry...obviously we don't often get to spend 20 or 30 seconds at high rpm/full noise on the road so I'd still be suspicious that is what is happening here.
    • MBS206
      Low oil pressure after WOT

      By MBS206 · Posted

      You are also getting pressure dips on gear shifts. They're just not dipping as far, but they're dipping quite below the amount of oil pressure you should be seeing, for how much RPM drops.   It quite little could be the oil pressure relief valve is starting to stick open a little/is slow to close.
    • MBS206
      Low oil pressure after WOT

      By MBS206 · Posted

      Can you log battery voltage, and TPS, and put all four of those into a single image (even as split graphs)?   The oil pressure drops aren't following RPM as such. I'm intrigued if you may have a ground loop between different sensors. With the engine not running, log your sensors and for example cycle the throttle pedal. See if any sensor values flutter or move about. This won't be a perfect test either as the ECU won't be cycling all of its actuators like it would be while running. What EMTRON do you have? Do you have a link to the wiring guide for that ECU?
×
×
  • Create New...