Jump to content
SAU Community

Fuel Pump

R338OY

By R338OY,
in Engines & Forced Induction

 Share

Recommended Posts

R338OY Veteran

R338OY

Posted
Posted (edited)

I've had issues with a new bosch 040 in my R33. It ran fine for a day but the pump fuse blew. I changed the fuse and the car started but when i tap the throttle there is a whirring noise coming from the boot (similar to priming) lasting a couple of seconds, and if i tap it a few times i hear the pump 'click' and the car shudders so i have to switch it off.

Does this sound like an issue with the pump/voltage regulator?

I was going to take it to Unigroup tomorrow and get it tested and reinstalled (it's already booked) but i doubt the car will make it out of my driveway.

Anyone know a mobile auto-electrician who knows Skylines? I'm near Parramatta.

Cheers

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/
Share on other sites
infamous_t Veteran

infamous_t

Posted
Posted (edited)

(Factory)Wire gauge is to small for your upgraded pump(it uses more power).

Needs a fresh run of thicker electrical wire, coupled with a relay to turn pump on/off.

Parts/wire shouldn't cost more than $40, labour will be more expensive, up to 2-3 hours for those not familiar with skylines.

Edited by infamous_t
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3696880
Share on other sites
R338OY Veteran

R338OY

Posted
  • Author
Posted
You paid a punk to install it, its his issue man! lol

Need more info, and as you didn't install it, ppl be stabbing wildly.

Unigroup seems pretty good, Yavuz will sort you out man.

Get to organizing that tow man for tomorrow man :)

Yeah Yavuz has worked on the car before. Spoke to him today and he's doing me a favour to look at it! Worst case scenario i'll have to tow it :D

(Factory)Wire gauge is to small for your upgraded pump(it uses more power).

Needs a fresh run of thicker electrical wire, coupled with a relay to turn pump on/off.

Parts/wire shouldn't cost more than $40, labour will be more expensive, up to 2-3 hours for those not familiar with skylines.

That sounds pretty convincing to me. I thought it might be $2-300 labour to call someone out, plus other bits and pieces.

So is it better to call someone out or try get it to the workshop? I'm more confident in Unigroup because Yavuz knows Skylines very well.

Anyone have a contact?

Thanks for the advice.

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3696929
Share on other sites
R338OY Veteran

R338OY

Posted
  • Author
Posted (edited)
Getting some proper copper to an after market pump in a Skyline is key, but i wouldn't thi... wait..

You have a R33, the battery's already 100cm away from the pump :ninja:

Make sure you let us knows what the issue was :)

Will do lol :happy:

If anyone has a contact let me know. It'll save calling some random electrician.

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3697118
Share on other sites
infamous_t Veteran

infamous_t

Posted
Posted
Getting some proper copper to an after market pump in a Skyline is key, but i wouldn't thi... wait..

You have a R33, the battery's already 100cm away from the pump :(

Id don't own a 33 to verify myself, but I would imagine the signal still comes from the ecu, which is still up the front of the car.

I forgot about this myself, but should make parts total cheaper (less cable).

Good luck mate :(

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3699813
Share on other sites
evil_weevil Grand Master

evil_weevil

Posted
Posted

Omar,

What time will you be at Unigroup?

Im heading there friday around 11am.

Yavuz and the team look after my boat, he'll get it sorted.

I've got a Walbro in there, few months back I had some mods finished and my fueling system was playing up.

Turns out that it was the low/high voltage for the fuelling.

I dont know too much on it, but apparantly when the car is at idle, it used a low voltage sender and when it gets up and going, uses the higher voltage. Mine was having dramas with that dual voltage and now it just runs on the high.

I cant notice any difference but fixed the issues.

:domokun:

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3700120
Share on other sites
R338OY Veteran

R338OY

Posted
  • Author
Posted (edited)

Well after frying 5 fuses to get to Unigroup (distance- 3 min drive) i finally had it looked at. Turns out the positive wire on the pump had been squashed between the pump bracket and tank. The reason it drove fine at first was because the wire wasn't grounding on the tank- until bumping around cut into the wire and lead to the shorting out.

All it needed was a zip tie to hold the wires in place and careful reinstallation. 30 mins labour and the car drives fine and revs out nicely :thumbsup:

Omar,

What time will you be at Unigroup?

Im heading there friday around 11am.

Yavuz and the team look after my boat, he'll get it sorted.

I've got a Walbro in there, few months back I had some mods finished and my fueling system was playing up.

Turns out that it was the low/high voltage for the fuelling.

I dont know too much on it, but apparantly when the car is at idle, it used a low voltage sender and when it gets up and going, uses the higher voltage. Mine was having dramas with that dual voltage and now it just runs on the high.

I cant notice any difference but fixed the issues.

:)

Cheers,

Chris

Hi Chris, i got there yesterday arvo, about 6pm. If i went today you'd be able to see how annoyingly minor the issue was! :P

Good to hear you sorted your voltage out- is the dual system going bonkers a common thing? Does the car just run sluggish with this problem? I'd like to know so i can recognise the signs.

Cheers mate

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3700940
Share on other sites
R338OY Veteran

R338OY

Posted
  • Author
Posted
Omar,

Mate unfort I couldnt tell hey!

When it was on the dyno for final tuning, thats when the problem occoured.

So yeah, sorry I cannot give you a better answer mate! ;)

No worries mate, but cheers for the info. If i ever get the same problem you'll be first to hear about it!

Doh - amateur hour

Going to let us know who did the work, so we can boo them :spank:

jk, don't do that.

Lol. Yeah guess that's the DIY risk- but i don't mind :cool:

The mate who installed it came along and Yavuz gave him a little booing for soldering the terminals. Hehe i thought he was about to clip him over the ear :D

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3702063
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      MLR's Bogan cruise ship

      By Kinkstaah · Posted

      Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
    • sonicii
      Mechanic in Victoria

      By sonicii · Posted

      I would agree, unless you need something specific to the HV motor/battery side repaired or investigated, any mechanic will be able to perform normal services, but if you prefer, maybe look for a mechanic who regularly services/repairs Nissans, the VQ engines are pretty common in the Nissan lineup.  Sorry, I can't make any suggestions, I don't live in Vic.
    • GTSBoy
      R32 GTR clutch master cylinder adapters

      By GTSBoy · Posted

      Some of them keep working fine. 9 out of 10 of them end up causing an absolute misery bleeding the system and get thrown on the workshop floor in a tantrum and never thought about again because they were never really needed and just added crap to the car that we could have done without. Same-same with HICAS, A-LSD, and various other stupidities that over eager 10x engineers thought we had to have.
×
×
  • Create New...