Jump to content
SAU Community

Recommended Posts

I've had issues with a new bosch 040 in my R33. It ran fine for a day but the pump fuse blew. I changed the fuse and the car started but when i tap the throttle there is a whirring noise coming from the boot (similar to priming) lasting a couple of seconds, and if i tap it a few times i hear the pump 'click' and the car shudders so i have to switch it off.

Does this sound like an issue with the pump/voltage regulator?

I was going to take it to Unigroup tomorrow and get it tested and reinstalled (it's already booked) but i doubt the car will make it out of my driveway.

Anyone know a mobile auto-electrician who knows Skylines? I'm near Parramatta.

Cheers

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/
Share on other sites

(Factory)Wire gauge is to small for your upgraded pump(it uses more power).

Needs a fresh run of thicker electrical wire, coupled with a relay to turn pump on/off.

Parts/wire shouldn't cost more than $40, labour will be more expensive, up to 2-3 hours for those not familiar with skylines.

Edited by infamous_t
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3696880
Share on other sites

You paid a punk to install it, its his issue man! lol

Need more info, and as you didn't install it, ppl be stabbing wildly.

Unigroup seems pretty good, Yavuz will sort you out man.

Get to organizing that tow man for tomorrow man :)

Yeah Yavuz has worked on the car before. Spoke to him today and he's doing me a favour to look at it! Worst case scenario i'll have to tow it :D

(Factory)Wire gauge is to small for your upgraded pump(it uses more power).

Needs a fresh run of thicker electrical wire, coupled with a relay to turn pump on/off.

Parts/wire shouldn't cost more than $40, labour will be more expensive, up to 2-3 hours for those not familiar with skylines.

That sounds pretty convincing to me. I thought it might be $2-300 labour to call someone out, plus other bits and pieces.

So is it better to call someone out or try get it to the workshop? I'm more confident in Unigroup because Yavuz knows Skylines very well.

Anyone have a contact?

Thanks for the advice.

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3696929
Share on other sites

Getting some proper copper to an after market pump in a Skyline is key, but i wouldn't thi... wait..

You have a R33, the battery's already 100cm away from the pump :ninja:

Make sure you let us knows what the issue was :)

Will do lol :happy:

If anyone has a contact let me know. It'll save calling some random electrician.

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3697118
Share on other sites

Getting some proper copper to an after market pump in a Skyline is key, but i wouldn't thi... wait..

You have a R33, the battery's already 100cm away from the pump :(

Id don't own a 33 to verify myself, but I would imagine the signal still comes from the ecu, which is still up the front of the car.

I forgot about this myself, but should make parts total cheaper (less cable).

Good luck mate :(

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3699813
Share on other sites

Omar,

What time will you be at Unigroup?

Im heading there friday around 11am.

Yavuz and the team look after my boat, he'll get it sorted.

I've got a Walbro in there, few months back I had some mods finished and my fueling system was playing up.

Turns out that it was the low/high voltage for the fuelling.

I dont know too much on it, but apparantly when the car is at idle, it used a low voltage sender and when it gets up and going, uses the higher voltage. Mine was having dramas with that dual voltage and now it just runs on the high.

I cant notice any difference but fixed the issues.

:domokun:

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3700120
Share on other sites

Well after frying 5 fuses to get to Unigroup (distance- 3 min drive) i finally had it looked at. Turns out the positive wire on the pump had been squashed between the pump bracket and tank. The reason it drove fine at first was because the wire wasn't grounding on the tank- until bumping around cut into the wire and lead to the shorting out.

All it needed was a zip tie to hold the wires in place and careful reinstallation. 30 mins labour and the car drives fine and revs out nicely :thumbsup:

Omar,

What time will you be at Unigroup?

Im heading there friday around 11am.

Yavuz and the team look after my boat, he'll get it sorted.

I've got a Walbro in there, few months back I had some mods finished and my fueling system was playing up.

Turns out that it was the low/high voltage for the fuelling.

I dont know too much on it, but apparantly when the car is at idle, it used a low voltage sender and when it gets up and going, uses the higher voltage. Mine was having dramas with that dual voltage and now it just runs on the high.

I cant notice any difference but fixed the issues.

:)

Cheers,

Chris

Hi Chris, i got there yesterday arvo, about 6pm. If i went today you'd be able to see how annoyingly minor the issue was! :P

Good to hear you sorted your voltage out- is the dual system going bonkers a common thing? Does the car just run sluggish with this problem? I'd like to know so i can recognise the signs.

Cheers mate

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3700940
Share on other sites

Omar,

Mate unfort I couldnt tell hey!

When it was on the dyno for final tuning, thats when the problem occoured.

So yeah, sorry I cannot give you a better answer mate! ;)

No worries mate, but cheers for the info. If i ever get the same problem you'll be first to hear about it!

Doh - amateur hour

Going to let us know who did the work, so we can boo them :spank:

jk, don't do that.

Lol. Yeah guess that's the DIY risk- but i don't mind :cool:

The mate who installed it came along and Yavuz gave him a little booing for soldering the terminals. Hehe i thought he was about to clip him over the ear :D

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3702063
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...