Jump to content
SAU Community

Rb25 Hks 2835 Pro-s Kit Infor


Tungnissan
 Share

Recommended Posts

ball park is around 260kw ish at the rears

the kit would be just short of $3k delivered including all the junk etc

you have two rear housing options being 0.68 and 0.87 for the rb25

from memory and previous posts from guys who have used it - most have said go the 0.87 rear

you can check the rb25 turbo upgrade thread and look for some users who have fitted the 2835 to their rb25 and their dyno results

Link to comment
Share on other sites

Dezz, i thought 2835's were 400ps just like the GTRS, its the 2835R's that are 420ps?!?

Havent sniffed around those parts in awhile, but I got the impression the GTSS and GTRS were successors to the 2530's and 2835s?!?

Can sum1 clarify?

Go a 3037 :)

Link to comment
Share on other sites

GT-SS is not a 2530 replacement.

GT-SS is similar to R34 N1's, a 2530 is bigger than a GT-SS.

GT-RS/2835, not much between the two really.

GT-RS is not a 2530 replacement either, GT-RS is bigger than a 2530

Link to comment
Share on other sites

thats what I meant:

GT-SS = 2530 --350ps

GT-RS = 2835 --400ps

Or there bouts :)

U on Niteshift too Mr Ash?

I was oncall :)

The "=" above, aren't.

GT-SS is smaller than 2530 -

ah, just realised my post was a big backwards (fixed it)

Link to comment
Share on other sites

  • 4 weeks later...
thats what I meant:

GT-SS = 2530 --350ps

GT-RS = 2835 --400ps

Or there bouts :rant:

U on Niteshift too Mr Ash?

HKS GT2835 - 380/400/410 PS Output (This turbo is N/A to skylines as the mounting is flange is different.GT25 inlet, skyline is T3

HKS GT2835 Pro S - 420 PS Output T3

HKS GT2835R - 420 PS Output GT28 flange

HKS GT-RS - 400 PS Output

Thus, the only turbo (in the 2835 range) you will be able to fit onto the skyline is a Pro S which is rated at 420, 20 more PS than the GT-RS.

Edited by Turbz RB-25
Link to comment
Share on other sites

  • 3 weeks later...
  • 2 months later...
  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • I am using a pull nismo coppermix twin in an r34 getrag box, had both the standard slave and  then the nismo one. Adjusted pedal to get bite point how I wanted , it is on the higher side, but would fully disengage past half way down.  I also read that the nismo slave won't work but I had no issues with the stroke, might become one later as clutch wears but 2+ years of happy motoring so far.  Take the above as one input only, specially as my setup is a bit unique in that I am using an S15 clutch master , cefiro clutch pedal, custom braided clutch line. Lots of variables at play. 
    • Oh for sure, I'm just recounting my thoughts 😎 I'm not what you've got there to fuzt with.... likely my first idea was on the money -- rebuild or replace connectors. You can get a lot of connector stuff here  -> https://www.rapidcables.com.au/ Didn't look in the boot of mine, because I replaced these when I renewed the pump (plastic of connectors had gone brittle) edit: what I used... https://www.efihardware.com/products/2120/Deutsch-DTM-Connector-Kit-6-Pin ...cheaper... https://www.ebay.com.au/itm/364900039138
    • In no way was i suggesting it’s your fault mate. The trailer cable has a plug that I removed. I will have a closer look, but I did remove the trailer wiring cable with the tow ball as I don’t need it on my silo. i have replaced the fuel pump already there’s no need to remove the cradle again I can see the wire colours from it in.
    • Mint. Good to see another GTSt getting love and coming back to life. Did I miss what colour you are going to wrap it?
×
×
  • Create New...