Jump to content
SAU Community

Recommended Posts

D-Link Wireless Access Point, 54Mbps - all complete and perfect order -$45

Netgear 54Mbit USB wireless adaptor - just plug it into any USB port and you have Wireless - $25

D-Link 54Mbit PCMIA (laptop) Wireless card - unused (but tested) - $40

Socket 478 1.7Ghz Celeron CPU - $35

Dakai 30A power supply, with Volt and Amp meters - $145

Subaru Impreza front indicators (from 1995 model) - $10

2 x Ignition DVDs, issues 16 & 27 (latest issue) - $10

Honda Prelude windscreen decal, plus Prelude badges from 1988 model - $15

Sony Ericsson K508i Mobile phone with camera (also does video), good cond. in original box, manual, charger, etc. All complete.

(I think I have a data cable & car charger for this one as well.. will have to check!). Unlocked, suit any network. $65

Pick up from Kiama NSW or willing to post,

(postage cost will be based on Aus Post's online calculator)

Any question, please PM or email, Cheers!

post-46181-1204870466_thumb.jpg

post-46181-1204870482_thumb.jpg

post-46181-1204870572_thumb.jpg

post-46181-1204918589_thumb.jpg

Edited by Wayne_J
Netgear 54Mbit USB wireless adaptor - just plug it into any USB port and you have Wireless - $25

will this allow me to connect to another wireless card without need for a router or anything else?

Hiya,

Sorry for the delay in replying, my email alerts have suddenly stopped for some reason today...

I thought SAU had gone a bit quiet :)

The WG111 behaves in the same way as any network adaptor, so as long as it's been configured correctly, as in Ad-hoc (Peer ro Peer), then yes. I assume that's what you mean, you want to connect to another computer rather than an access point?

Some basic info on this adaptor here, see if you think it'll suit your needs:

http://www.netgear.com/Products/Adapters/G...ters/WG111.aspx

will this allow me to connect to another wireless card without need for a router or anything else?

Cheers,

  • 2 weeks later...
  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Exhaust end of this month, and then tune after that whenever there is availability. Still tossing up between a pure 98 tune or a flex 98/e85 combo.  The (lack of) milage in e85 isnt great. Start to get anxiety if i go for a long drive and there arent any united servo's nearby
    • I mean I can be OCD'y but this is really over the top. At that point why not just run a full wideband fuel controller? Especially if you run 3 widebands. The system works pretty well, which is trimming low load stuff to be within a few percent of the base map. Pre-engine _change_ the base map was only 1-2% off, depending on ambient temp, elevation, etc. Under load the LS is really very straightforward to tune, enough that a wideband closed loop would be overkill. If I really cared (and I hope I don't) I can always just go back to the MAF system the car actually came with. Which does all those nice calculations for me (temp, altitude, etc), now that you can buy 102mm MAF's that do not cause restrictions.
    • Good afternoon Team , just a quick update on performance mods  Current Mods list (Installed) HKS - Power Editor (Came with the car) looks to be some kind of boost controller RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Cat Back  RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Front Pipe AMS  - INFINITI Q50/Q60 RED ALPHA COLD AIR INTAKE KIT AMS  - Performance Heat Exchanger Intercooler Not Yet AMS Alpha Performance Full Race Down Pipes  - to be installed in May 
    • I'd be installing 2x widebands and using the NB simulation outputs to the ECU.
    • Nah, it's different across different engines and as the years went on. R32 era RB20, and hence also RB26, the TPS SWITCH is the idle command. The variable resistor is only for the TCU, as you say. On R33 era RB25 and onwards (but probably not RB26, as they still used the same basic ECU from the R32 era), the idle command is a voltage output of close to 0.45V from the variable resistor.
×
×
  • Create New...