Jump to content
SAU Community

Recommended Posts

Hi

We are clean all the old stock out and clean up the garage.

so there is few parts up for sale now.

R34GTR

STD injector x6 $250

STD fuel rail with std fuel regulator $80

STD cam shaft $120

STD Cam gear $50

STD Valve spring $50

STD intercooler $300

STD Exhaust system $500

STD Airbox with snorkel $300

STD BOV with pipe $250

STD clutch $100

STD exhaust system $90

STD front pipe $80

STD cat $ 80

STD radiator $200

ARC radiator $700

STD Rear Bumper $700

STD AFM $460

R33GTR

Nismo O/H twin plate clutch $1700

Head lights $500

Tail shaft $200

STD gearbox $750

AFM $300

Used water pump $50

Used oil pump $100

Passenger seat $500

Front bumper $500

Factory side skirt $200

STD suspension $300

STD cam shaft $100

STD Cam gear $40

STD valve spring $40

STD injector x6 $200

STD Fuel rail with fuel regulator $60

STD bov with pipe $220

STD intercooler pipe $200(got twin turbo on top)

STD exhaust manifold $60

STD front pipe $50

STD cat $30

GTR33 V-spec diff (complete) $500

STD intercooler $280

STD radiator $160

R34GTT

STD exhaust system include cat $180

R34GTT injector $140

R34GTT cam shaft $80

R34GTT intercooler $180

R34GTT rims x3 $300

STD R34 turbo need O/H $150

R33GTST

STD front bumper $100

Boot white $200

STD heater box $150

STD rear spoiler $100

STD side skirt $100

STD suspension $140

STD Airbox $120

STD airbox snorkel $45

STD BOV $30

STD intercooler S2 $130

Tanabe suspension $500

STD fenders(pair) $280

350Z

STD exhaust system (complete) $300

STD suspension $150

S15

STD intercooler $80

STD front brake system (complete) $400

Passenger Fender $200

Supra (JZA80)

STD Auto speedo $100

STD intercooler $100

EVO7

STD suspension $200

STD airbox $100

STD ECU $150

STD tail light $200

STD front bumper $280

MRS

STD head lights $300

STD body kit (full kit) $450

STD engine need O/H $800

Brand new engine done 1500km with head work $2500

MR2

N/A engine $500

Radiator $50

Rx7 (s8 2001)

Bilsten suspension done 5000km $750

STD intercooler $180

STD seats front and rear $900

STD turbo $1400

STD Front brake kit off RS(bigger than S6/S7/RB S8) $1100

STD rear rotors $200

Boot trim complete $250

Roof trim $120

Complete carpet $200

BMW E36 318

STD wheels with tyres 15 inch (near new tyres) $300

Radiator $100

A/C candensor $140

180SX 1.8L

Brand new Trust Intercooler kit $1450

Honda H22A

Complete Engine/Jun cam shaft/Jun cam gear/Jun Valve spring/Jun retainer/Aftermarket head gasket

Botton end need O/H

$3500

used Trust Twin entry intercooler 600x286x75 $500

Jap brand GTR 600x300x100 intercooler $750

please reply to us if you need anything

Thank you very much

Edited by GTAUTO
Link to comment
https://www.sau.com.au/forums/topic/209353-gt-auto-garage-sale/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hows your intake piping? Are you still running stock? Having in the stock AFM position would mean, if the BOV was shut/venting out, it'd create the almost stalling kind of effect right // "the rich pulse behaviour" due to MAF thinking air is flowing ? But this would be better than having the bov in the stock position + MAF on/just before cross over piping right?
    • Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
×
×
  • Create New...