Jump to content
SAU Community

33 Gts Non Turbo Manual Complete Car $4500

Guest darrinspencer

By Guest darrinspencer,
in For Sale (Private Car Parts and Accessories)

 Share

Recommended Posts

Guest darrinspencer

Guest darrinspencer

Posted
Posted

Non turbo 1994 33 2 door manual complete no damaged.

THIS VEHICLE CAN NOT BE COMPLIED. ONLY GOOD FOR PARTS.

Bonnet , head lights and radiator missing, other wise complete.

Perfect for a writen off body shell replacement or as a drift car or parts.

At this stage selling complete as is.

DoughBoy Veteran

DoughBoy

Posted
Posted
Originally posted by bryanlee38

Why dont u just wait till there's more compliencing plates being circulated then get it complied and keep the car then. WOuldnt that be wiser?

Approval for vehicle compliance needs to be started before the car is shipped over. I was under the impression that if it's brought over without initial approval it had to be destroyed - and proof shown. How did the car get in to the country? Was it accepted for compliance before the 7th May cutoff and no plates could be found to finish the job?

Xeaon Collaborator

Xeaon

Posted
Posted

Jordan or whom every buys it I'm willing to pay good money for these parts if in perfect working order ect.

g'box, pedals, pedalbox, clutch master cylinder, drive shaft, g'box mount and cross members, center console,gear stick, gear stick cover, pressure plate, clutch (if in good condition) flywheel, gear knob.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • cabramatta
      Never ending fuel pump drama

      By cabramatta 路 Posted

      Might piggy back off this thread since there's been a good discussion about PWM.   I purchased a Walbro 460 F90000267 and have been looking into PWM to understand it. It was purchased more of a future proof as my original OEM fuel pump died (r33 below 200kw) and figured I'd just upgrade it to this. That's when it hit me that a pump this big can cause more dramas with such high amperage draw and heating of the fuel pump being on 100% all the time in such a mild setup.   I have a Nexus R3 and slowly collecting power mods but I was looking into the PWM feature on the NSP software:   Then looking at the graph from the fuel pump:     Am I safe to assume reducing duty cycle to 50% for example would make the pump run like a 230/lph ? Where does the PWM come in all of this ?   I've gone down the rabbit hole of PWM fuel pumps and it seems there are many differing opinions on how to go about it 馃槄  
    • DRoc81
      Shifting questions

      By DRoc81 路 Posted

      Thank you, this will keep me busy for a bit.  I will update progression.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 路 Posted

      That specific one would be an exchange part, meaning I'd have to send mine to them. Plus it looks like a non AWD sump, which won't work for me. There is one or two shops in my country that I can ask to do a sump extension job and it'd most likely end up being cheaper than sending mine to AUS or NZ and getting one back, and quicker too.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 路 Posted

      Rear turbo is leaky, most likely at the oil drain. From what I could see with my boroscope it seemed to have seeped out at the very top of that return hose. Is it possible that the oil climbs up that hose to then leak out? Yup, coolant leak on the hot side of the engine, only noticed after seeing clear rusty residue in the block right from the turbo oil feed downwards to the pan, and red droplets hanging from the pan. No clear sign yet from where it comes, and most of the lines there are hardlines right? Last year, seeing those red drops, I thought it was power steering, will be glad if that is not leaky at least. Another leaking hose I found by chance is the lower of the two heater core hoses coming from the firewall to the back of the head. That one is not too bad to get to if I have to replace.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 路 Posted

      I think for response I'm already kind of out there no? he -5s are not the best pick for that as the Internet tells me. Maybe I should switch to -7s while I still can? Though that almost definitely warrants an engine pull along with the other issues I have.
脳
脳
  • Create New...