Jump to content
SAU Community

Recommended Posts

If your talking Brissy powercruise NYTSKY im sure ill be there with mine and Id love to go ya just to see how a built 25 v built 26 goes :blink: should be able to turn the key this weekend ;):)

Edited by johnbarry88
That CAS was fine when it was on the last motor - couldnt get any sand in there from the bottom end letting go

EDIT: Although, that car has a mind of its own

Its ok steve-o...ive got a free replacement...no probs mate. Did you get the "twoogle" CAL. file for the autronic?

Its ok steve-o...ive got a free replacement...no probs mate. Did you get the "twoogle" CAL. file for the autronic?

Ok cool thats a relief

Yep all good, thanks again. Car is on its way to CRD right now for a run in tune, then ill send the twoogle tune for the serious tune

Ok cool thats a relief

Yep all good, thanks again. Car is on its way to CRD right now for a run in tune, then ill send the twoogle tune for the serious tune

Jim was reluctant to fit the Autronic to my car...but he's tuning yours...no love.

The tune in the unit now is Guilt-toy's RB25 tune...may have been better loading mine in.

He needs to bridge the TPS signal to the ATTESSA ecu to give the car 4WD.

Im reconditioning your CAS...i think the noise was from me cleaning it and the gasket not sealing the unit properly (no fault of yours)

Edited by DiRTgarage

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, so all I can suggest is that - if you have all the parts, and you have all the wiring looms, and you have all the electronic modules, then....it really is just a wiring problem. You likely have a damaged wire, pin, etc, somewhere.
    • Yup, bought this bad boy and hopefully it will be ready to pickup today. Had $5 credit on top of it so it worked out really well!
    • Yeah it is really until until you get a feel for it....then it is easy. Which is no use to you really. I'd buy that torque wrench. One thing from sure, many (most?) tyre shots overtighten the f**k out of wheel nuts, so don't worry if they were tighter when you tried to take them off compared to when you do them up. I've had some crazy tight ones come back from shops, quite apart from the potential damage to the thread, I can't see a smaller person taking the wheel off on the side of the road
    • Hey mate, thread dredging hahah To answer you directly, yes I had my itbs oversized and custom butterflies etc made by EFI Hardware in Sydney back around 2017-2018 if memory serves. My setup had a vast amount of other changes too though, so no direct comparisons unfortunately. i went from oem itbs, HPI manifold and internal gate hks 2835 pro S; to 49mm itbs, cnc port matched Nismo plenum, RB25 Neo lower runner adapter hand port matched, r31house v2 Takoashi MAX equal length twin scroll manifold with twin 38mm tial gates and a FP HTA3076 with 1.01ar twin scroll real hosing. feom power Fc to a link fury wired by 12volt, r32 gtr fuel tank conversion with frenchys twin 460 / surge tabk fuel hanger combo kit, 1659cc injectors, full 4 inch turbo back stainless exhaust, Z34 6 speed, Tomei 2way with 4.3 final drive and a ton of other shit. ive posted elsewhere here with complete run down, but here's a graph from its initial tune with no boost control on, 20psi gate springs only and e85.   7542AE72-DA92-4E0B-8660-B0940FEA7F24.mov
    • On sale mate, $55. Sorted. https://www.supercheapauto.com.au/p/toolpro-toolpro-torque-wrench-1-2-drive/565734.html?utm_content=paidsearch-pmax&gad_source=1&gclid=Cj0KCQjwytS-BhCKARIsAMGJyzqYEnwWmhWf6gxTST_Nz06Gd2VePgyvL7lh6PWrQtbjXTsI6TqSCLEaAuaCEALw_wcB&gclsrc=aw.ds
×
×
  • Create New...