Jump to content
SAU Community

Recommended Posts

think that might have been me
did u have a nice green p plate up?? lol

late reply but yep i got nice green P plates up on my car haha =\

think i spotted 'CosmoKram3r' last night around 1045pm or 11 ..

blue r32 turned out of a street onto princess hwy heading towards hallam pub.

numbler plate on the lower part of the bumber maybe front right

haha yeahh that was me man i was dropping a mate off and heading back home

blue 32 with black bonnet in narre @ fountain gate

ive been going to fountain gate quite a bit lately that was prob me..

Edited by cosmokram3r

Ummmmmmmmmmmmm yea was on the way to pick up a BBQ with my mate in the work ute we say this and i creamed my pants .... lol just thought i would share !

Ps:Gotta love the Nokia 95 8G

post-51556-1227750794_thumb.jpg

post-51556-1227750936_thumb.jpg

post-51556-1227750850_thumb.jpg

Edited by _K1NGTR_

It was on Greens Rd we were turning on we almost had an accident in the ute trying to catch up to it lol yea plastics all over it had some gay toyota behind it but almost every car had there eyes on it so distracting ....!

Ummmmmmmmmmmmm yea was on the way to pick up a BBQ with my mate in the work ute we say this and i creamed my pants .... lol just thought i would share !

Ps:Gotta love the Nokia 95 8G

wtf is that on the front bar? is it a tow point if so looks shit house wrecks the whole front bar.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
×
×
  • Create New...