Jump to content
SAU Community

Recommended Posts

Was meee, saw ya 2 buddy and ur last second wave....i waved 2 hehehee had a feelin was u and nearly in the same place :)

yea, i live in that area :P and my parents owns that bottleshop on lower dandy:D

I'm confused as to what NZMO actually is. It's an R34 with badges say GTS-R.

WTH??

i bought my front bar off him llol. i remember when he was doing the stuff to his car. pretty sure its a GTT converted to look like a GTR making it a GTS-R or something like that

i bought my front bar off him llol. i remember when he was doing the stuff to his car. pretty sure its a GTT converted to look like a GTR making it a GTS-R or something like that

OIC... makes sense now. That's a pretty good conversion.

OIC... makes sense now. That's a pretty good conversion.

Yeah its a conversion(Top Secret GTR front bar and Z-Tune GTR Bonnet) front diffuser ready to go on , thanks for compliment,you took a nice photo of it, i used it for my desktop.

cheers,

David

spotted Nick gtstsedan in his undies outside his gfs house this morning

geez man, wear a ROBE

lol the chiks dig it :laugh:

Finally after five years i've been spotted. Nick it's actually dark blue, but green's cool too. I was getting some motul and bits and pieces. :thumbsup:

ahk

yeh i was to :laugh:

you from around the area?

CNBLOW at the keilor village pub (great pub)

Spotted you as well Paul, i was actually across the road at the park for a birthday. While i was there spotted a grey kitted 32 with black TE37 wheels? gees it was loud!!, it had a writing which said 73 on the windscreen, possibly from the drags? for some reason i think it was "Roy"'s car, but could be wrong

spotted a silver R33 GTR with a carbon hood and SAU stickers

also spotted a tuff R33 GTR with no wing on the great ocean road

went past a workshop that had a heap of GTRs, stageas, anything with an RB. the OH R34 gtr was there too

Edited by GTR-boy
spotted a silver R33 GTR with a carbon hood and SAU stickers

also spotted a tuff R33 GTR with no wing on the great ocean road

went past a workshop that had a heap of GTRs, stageas, anything with an RB. the OH R34 gtr was there too

sounds like OH Performance on McIntyre (sp?) rd in Sunshine

spotted a silver R33 GTR with a carbon hood and SAU stickers

also spotted a tuff R33 GTR with no wing on the great ocean road

went past a workshop that had a heap of GTRs, stageas, anything with an RB. the OH R34 gtr was there too

the purple one? thats a gtt with a rb26 its not a gtr

looks like they've taken over that nismo joint next door aswell...?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Lucky man, who owns it in the family? Any pics? 
    • The engine stuff is Greg Autism to the Max. I contacted Tony Mamo previously from AFR who went off to make his own company to further refine AFR heads. He is a wizard in US LS world. Pretty much the best person on earth who will sell you things he's done weird wizard magic to. The cam spec is not too different. I have a 232/234 .600/603 lift, 114LSA cam currently. The new one is 227/233 .638 .634. The 1.8 ratio roller rockers will effectively push this cam into the ~.670 range. These also get Mamo'ified to be drilled out and tapped to use a 10mm bolt over an 8mm for better stability. This is what lead to the cam being specced. The plan is to run it to 6800. (6600 currently). The Johnson lifters are to maintain proper lift at heavy use which is something the LS7's supposedly fail at and lose a bit of pressure, robbing you of lift at higher RPM. Hollow stem valves for better, well everything, Valve train control. I dunno. Hollow is better. The valves are also not on a standard valve angle. Compression ratio is going from 10.6 to 11.3. The cam is smaller, but also not really... The cam was specced when I generated a chart where I counted the frames of a lap video I had and noted how much of the time in % I spent at what RPM while on track at Sandown. The current cam/heads are a bit mismatched, the standard LS1 heads are the restriction to power, which is why everyone CNC's them to get a pretty solid improvement. Most of the difference between LS1->LS2->LS3 is really just better stock heads. The current cam is falling over about 600rpm earlier than it 'should' given the rest of my current setup. CNC'ing heads closes the gap with regards to heads. Aftermarket heads eliminate the gap and go further. The MMS heads go even further than that, and the heads I have in the box could quite easily be bolted to a 7.0 427ci or 454 and not be any restriction at all. Tony Mamo previously worked with AFR, designed new heads from scratch then eventually founded his own business. There he takes the AFR items and performs further wizardry, CNC'ing them and then manually porting the result. He also ports the FAST102 composite manifold: Before and after There's also an improved racing crank scraper and windage tray. Helps to keep oil in the pan. Supposedly gains 2% power. Tony also ports Melling oil pumps, so you get more oil pressure down low at idle, and the same as what you want up top thanks to a suitable relief spring. There's also the timing chain kit with a Torrington bearing to make sure the cam doesn't have any thrust. Yes I'll post a before and after when it all eventually goes together. It'll probably make 2kw more than a setup that would be $15,000 cheaper :p
    • Because the cars wheels are on blocks, you slide under the car.   Pretty much all the bolts you touched should have been put in, but not fully torque up.   Back them off a turn or two, and then tighten them up from under the car with the wheels sitting on the blocks holding car up in the air.
    • Yes. Imagine you have the car on the ground, and you mine away all the ground under and around it, except for the area directly under each individual wheel. That's exactly how it'd look, except the ground will be what ever you make the bit under each wheel from
    • Yes, if you set the "height" right so that it's basically where it would be when sitting on the wheel. It's actually exactly how I tighten bolts that need to be done that way. However....urethane bushes do NOT need to be done that way. The bush slides on both the inner and outer. It's only rubber bushes that are bonded to the outer that need to be clamped to the crush tube in the "home" position. And my car is so full of sphericals now that I have very few that I need to do properly and I sometimes forget and have to go back and fix it afterwards!
×
×
  • Create New...