Jump to content
SAU Community

Membership

Tiiger

By Tiiger,
in Victoria

 Share

Recommended Posts

Tiiger Contributor

Tiiger

Posted
Posted

Hey guys,

I just sent in a membership form and DD payment (on the 18/3 payment has gone through) and was wondering how long it takes to get the membership card as I need it for the 10th April.

Sorry to post what is probably a question asked a million times elsewhere, I did do a search but didn't find anything, then again I am blonde..... :D

Cheers,

JK

Link to comment
https://www.sau.com.au/forums/topic/211241-membership/
Share on other sites
Tiiger Contributor

Tiiger

Posted
  • Author
Posted
14 working days Jenna, I think thats on the Membership form itself (honestly not 100% sure hehe)

So I would be very confident it will be sorted by the 10th of April for you.

Cheers.

Thanks heaps for the reply R31Nismoid, most appreciated! :D

Link to comment
https://www.sau.com.au/forums/topic/211241-membership/#findComment-3735183
Share on other sites
Kaz200 Grand Master

Kaz200

Posted
Posted

Hey Jenna! Can you email me the form? [email protected]

Will be able to process it faster for you.. alternatively if you just email me your name, address, I'll fix up the rest when your form arrives.

I have confirmation of your payment already (thanks Rossco!), so if you're still live in 'the same area I spotted you in'... I might be able to drop your card off over the weekend even!

Chat to you soon,

Cheers!

~Kaz

Oh and it's 15 working days but 90% of the time it only takes up to about a week...

Link to comment
https://www.sau.com.au/forums/topic/211241-membership/#findComment-3735851
Share on other sites
Tiiger Contributor

Tiiger

Posted
  • Author
Posted

Hi Kaz, thanks for that. I've been in Perth over Easter but Dan sent you an email so if you could reply to him that would be great. We fly out for Targa on the 13th so I need the card before then if possible, or a letter with my membership details on it.

Cheers and thanks again! :ninja:

Jenna

Link to comment
https://www.sau.com.au/forums/topic/211241-membership/#findComment-3746245
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Hypergear Turbochargers and High flow Services Development thread

      By Dose Pipe Sutututu · Posted

      Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
    • cardre
      My R32 Money Pit & The Headaches That Come With It

      By cardre · Posted

      Awesome writeup and details. Thanks for sharing the story so far. I can relate to parts of it with my previous car and some of the issues I had to deal with.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Wow the colour matched hard top completely transforms the car. Are there any nice front lip options for the car or is that off the table?
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Generally yes but for some reason I've been ruthless this time around!  I might even need to do another tip run after the way I've finally been able to hit the delete button on shit I've stepped over, stepped around and tripped over for the past 10 years!
×
×
  • Create New...