Jump to content
SAU Community

Recommended Posts

Hi everyone. I have just brought my new GTR 33 and yesterday was driving it around, I went around a corner in second gear and changed a 5 revs, the car then sort of almost stalled, and had no reving power at all it just idles at around 1 rev. I turned the car off and on and the problem disappeared. Again today same thing only twice it happened. I could feel the car getting a little sluggish and then........ back down to 1 revs with no power the car would just roll to a stop! Does any one know what this could be? Do you think it has any thing to do with the boost controller which I have not touched since i brought the car. It has only 12,000kms on the clock.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/21127-gtr-almost-stalls-when-boost/
Share on other sites

Air flow meter? Was having probs with my gts-t. Every now and then it'd get a bit sluggish and the revs would drop. Stalled a few times, other times I'd get something like engine/fuel cut out at about 2500 rpms - there was no way the revs could get over 2500. Started happening at 1000 rpm last week got it checked out and found out the air flow meter was stuffed. I've replaced it and havent had a prob since.

mickGTR - might be an idea to see if you can find a workshop which has the new Snap-on computer system. I'm not sure exactly what its called but I know its reasonably new. You plug catridges (compatible to the car) into it and then connect to a particular point on the car and it will instantly computer diagnose the problem.

I have been having trouble with my GTS-t,

It feels like it is surging when I put the foot down,

It was boosted @ 12 psi, went in for service And came back with this problem we thought it could be the cpu,

I said it shouldnt be the battery went flat so we thought could lead to the problem, change that still there, so its going in on friday, and we are going to look at the fuel filtter this time.

I have had the same problem, just got my car back from nissan, it sounds like an afm problem, element could be dirty or connection loose, i doubt you would have the same prob i did but inside the connector box on the afm, some the pins inside had their solder snapped off, they were still touching for a connection but it obviously wasnt giving out enough voltage to get a proper signal to the computer, nissan sent it off to get re-co'ed, the test and reco cost me around $120, but could be fuel pump or even igniter module but probly not, if the fuel pump was on the way out it would make some load whining sounds every now and then, and if the igniter module can be faulty when the car is warmed up

anyways hope this can help in anyway

Hi guys. Im having the air flow looked over by a mechenic today. Im not to sure if it will be that though, as sometimes the car runs beautifuly, and others, just out of the blue it will do as I mentioned. At first i thought it might be a problem with the boost controller...... but Im not sure as I dont know much about the mechenics of the car.

Regards

Mick

  • 2 weeks later...
Originally posted by wrxhoon

everyone should know that imports have been turned back and in japan not many people service their cars .

thats why u see a 12 yo car with 10-50 k k's

yeah i agree with ya ..

either they turn it back or they just replace the cluster ..

have seen 1993 GTSTs with 30k km and average 96-97 GTSTs are having like 100k km on them already ..

maybe they just turned back the first digit on the left side .. :uh-huh:

mickGTR, Yeah same thing was happening to me, changed the AFM on Monday now the car is fine.

12,000ks, sounds abit suss......

When I was looking arond for my car, there was a 98 skyline at the importer with about 100,000ks on it. Went back afew days later, same car less than 1/2 the amount of ks on it....

They all do it!

they dont replace the clusters ( extra expence ) the just turn them back usualy before they come in and almost always before they put them up for sale .

dont forget cars have a hard time in japan too .they dont do as many k's as they do here but always in traffic and not always seviced either.

i've had a few jap engines apart with lopw k's and they have plenty sludge inside , something u dont see in australian engines with very high k's like 300-400 k k's and the are still clean .

most peple here change the oil at least every 10 k k's and a lot of them use good oils .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are adaptors that allow you to delete the booster and use an s15 clutch master cylinder.    if you want to keep the booster they are still available brand new 
    • I visited again today: It would appear they have painted the main body of the car and some parts of some of the panels, so I can say that I now have BMW parts in my car, much to the envy of @Dose Pipe Sutututu It is still covered in dust which is quite the tease but I did look at a few circumspect spots that will be behind bumpers and such and wiped some dust away: After my repeated begging to PLEASE DONT PAINT OVER THE ENGINEERING CERTIFICATE (you have to re-engineer the entire car if they do) I see THIS: Which is great. Excellent job tbh at least to me. A better non dusty example would be the backs of the doors that have been painted: Giving a reasonable contrast between old and new (I know the old isn't clear coated on the inside of doors). The door card will well and truly cover where the old paint is, you can see in the second pic some of the black butyl/whatever shit is sticking the plastic sheet behind the door transfer that has happened since it's clearly been stuck back on. The most maddening thing about this colour is every time I saw it in the wild it looks like another colour, same with photos of many cars with the same colour looking wildly different in every photo anybody ever takes and this is no exception. But stand a little further back and it suddenly looks dark AF. I did tell them when I was discussing which of the 70 million charcoal colours to choose from (a porsche one, a BMW one, or a R32 GTR one etc) that if they just ignored me and chose one at random I would probably never notice. Maybe they did. But the colour is supposed to be B39 (BMW Mineral Gray). Boring I know, but the R34 sedan (to me) really shows off it's boat-ness when you paint it in a bright colour like bayside blue or white or whatever else. I do have a fondness for AR2 Nissan Red, but decided against that because it'll have pretty odd contrast to random bits unpainted (like engine bay, bits of trim etc, and maybe it'll fade). And people will always fkin comment on AR2. Everything remains super dusty. I have tracking numbers for the new heads, as well as some Improved Racing goodies, but they probably will be a next year thing by the time they end up on the car. I did some maths on the heads and I know why nobody goes to this extent in Australia, because it's really not worth it, given I could have just CNC'ed my current heads, bought a FAST102/TB and used my current rocker/spring/cam combination and get a 383 stroker (or stroked a 6.0 GenIV bottom end to 6.6L) built for the same price of just the setup in the mail/on the floor here. Or I could have bought a LS3 and a Drysump system. And then have a complete engine to sell. Oh well
    • We just disconnected the vacuum line if I remember correctly, booster is still there. Is there a rebuild solution for the booster or a different adapter that will work for GTR chassis?
    • Yeah 4wd (boosted) has a recess in the firewall for the booster, and 2wd is flat - the example in the link shows the flat surface. When you deleted the booster, did you just attach the factory slave cylinder directly to the recess in the firewall with no adaption?  
    • Yes, but no. You need to keep the mating surfaces bare (ie the flat faces where the caliper and upright pads touch the dogbone) and also the internal threads will remain bare (unless there are no internal threads - do they use nuts on all the bolts?). So you can slow down obvious external corrosion, but not all of it. Anodising would be required to provide decent protection to the alloy, but I'm not actually sure if you should anodise something that is all about the strength. Anodising does reduce strength significantly. Like, up to 50% on some alloys for high thickness coating.
×
×
  • Create New...