Jump to content
SAU Community

Recommended Posts

Hi People's

There's something wrong with my car. At the moment what happens is that when i put my foot down it gets up to about 5 psi fine and then just seems to stay there or even drop a little when it's on standard boost which is 7psi. When i put it on high boost which is 1 bar. It gets up to about 9 pound and is then very erratic and it's go up and then down a bit some times it rev's out and fine but feels very slow and other times up the top of the rev range it stutters a fair bit. when i turn the boost off it makes about 5-6 psi but the car just does not move. It revs out but just feels very very slow. When i give it rev's and drop the clutch (rear wheel drive) as soon as it hit's boost it just stutters). i looked at the power FC and everything looks fine and the injector duty cycle seems fine i can't see any leaks. and it ramps onto boost fine. All the interior guages seem fine. I have a metal cat but my car is just a street car could it be melted???

This Problem happened last night. I had it on high boost and was flooring it when at about 6000rpm it seemed to loose power and that problem has persisted to now.

The car's modified it has:

ACL Forged Pistons

ACL Piston Rings

ACL Big End Bearings

ACL Main Bearings

Ported and polished head

Stock polished crank and rods

Bored and honed Block

N1 Oil pump

N1 Water pump

Tomei Oil Gallery restrictor

Gates timing belt

New engine gaskets all round

New Thermostat

New NGK spark plugs

R34 GTR injectors

R34N1 turbos C106/GT25 A/R 0.60/0.64

New Rod bolts, welsh plugs

Fresh paint on rocker covers

3" Trust Front pipe and Power Extreme II Cat back Exhaust

3" Metal cat

Twin Apexi Pods

Apexi Power FC & Hand Controller

Greddy Profec B Spec II boost controller

Nismo fuel pump

i've changed spark plugs today checked for blow bye and everything seems fine. I really need some help.

Has any one had this problem before???

Edited by black sky
coil pack?

i doubt it's a coil pack because i got split fires not long ago. and some times it rev's out fine but it's just not making the right amount of boost and it feels really sluggish.

i just don't know what to do.

done a compression test yet ? I would start here just to put your mind at ease that its not the engine itself...

do you really think it could be the engine?? it's not blowing smoke, it gets onto boost fine, and the engine's been rebuilt not long ago. Oh god please tell me it's not the engine.

it could be a lot of things...but through the process of elimination you will narrow it down to certain areas..once you are 100% that the engine itself isnt the problem then you can attack other areas...Fuel or ignition..is where its most likely at....But first be sure that engine is perfect

Hey mate check all your hoses and look for leaks in your intercooler piping BOV etc. I found I had a similar problem with the boost (not spluttering though) currently there is a leak from the gasket going into the last of the throttle bodies (to be fixed next week), worth a try. I made a very simple device from here ( http://www.vfaq.com/mods/ICtester.html ) and blew compressed air into the engine and found it. cost $7 to make and and all you need to do is take off your air box, block one of the hoses from the AFM and place this in the other. (dont need the hosing as on the website just get 65mm PVC end stop fit in nicely)

hey mate, i have the same problem i have nail polished the coil packs, gapped spark plugs but no good i can only get 7 psi to rev cleanly on boost any more than 7 and it is like the rev limiter comes on at 6000 rpm.

i am onto it, will diagnose problem soon and let u know ... :D

hi, i just put a small vid on, this is what my car sounds like to 6000 rpm, quality of vid not too good

on the street

Congrats, your a tool :blink:

EDIT: Incriminating 'hooligan' link modified...

Thx

Edited by GeeTR

i don't think it's the intercooler piping as it comes on boost as normal and i don't think it's the splitfires because every now and then even on 14psi it revs out but just feels like crap.

but i am going to try that boost leak thing, it looks interesting.

but all indications make me think that it's a blocked CAT.

  • 3 weeks later...

Ok guys here's an update

I checked the cat all is good i checked the BOV and the same problem is occuring

i disconnected the Boost controller and it's just boosting up to .7 bar and it's fine but it was alway's like that only when i put it onto high boost does it stutter. any ideas???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
    • Thanks for taking the time to post that ! If anything changes or happens please do update us. 
    • Somehow Vertimass/Oak Ridge National Labs has figured out a catalyst that can convert ethanol into C9-C10 hydrocarbons in basically a single step without ending up with a bunch of ethylene or similar waste products: https://patents.google.com/patent/WO2023224867A1/en I still don't think anything like this will keep us from needing to transition to EVs regardless along with all kinds of other electrification, but things like this will go a long way towards alleviating the problem of how to electrify things like planes. Renewable diesel is seemingly an easier problem as well, Chevron is already running refineries for the stuff and the primary feedstock is tallow and other waste fats from agriculture.
    • Ok so I have sorted everything with my uniclutch and  i can offer up a bit of feedback and some things that might help others.    I found problems with factory damper line. Weird shit and had trouble with peddle adjustment    I used this https://au.gktech.com/products/r33-gts-t-skyline-braided-clutch-line?_pos=2&_sid=22b01b9b9&_ss=r Also when adjusting peddle leave a bit of play. You can get into a over stroke condition easy.. Make sure you can push the slave forward after adjusting to confirm fluid can return to master then you will need to pump it up heaps…..not sure why but that’s how it is.    last thing the splined adapter is machined perfectly. If your input shaft is old like mine was I would put a bit of valve grinding paste on it and stroke it like a 15 year old. Just to give it a tad more clearance and to better match it to the spline.    reason is on a near flat shift I have had situation where the peddle returns a millisecond after you lift from the clutch. No slip or anything but I reckon this is due to tolerance on the spline being way tighter than stock clutch and binding for a sec. I think this will go away but also my spline was old. Box is old so I guess I should have checked better. It’s a super neat fit.    it feels light as and holds awesome without any noise    
    • My Fuga Hybrid is JDM, 2014 model but very similar to the V37 from the looks of things..same platform just physically larger and very comfortab;e
×
×
  • Create New...