Jump to content
SAU Community

Flushing Radiator And Cooling System.

ak_stylez

By ak_stylez,
in General Maintenance

 Share

Recommended Posts

ak_stylez Community Regular

ak_stylez

Posted
Posted

hey everyone,

looked under my radiator cap about 5 months after having installed a new alloy radiator, and the coolant has turned from a nice clean green to a dirty brown. the state of the coolant was quite poor (even worse) before i replaced the radiator, and at the time we only flushed the system with water. My mechanic said the rusty water might return until i flushed it thoroughly with one of those radiator flush cleaner things from supacheap.

so, now its time to do just that. i had a look at some threads via search, and also a copy of the manual i found on the internet.

before getting started, i just wanted to make sure I had everything I needed.

here's a list of things i'll need that i compiled from both the manual and various threads:

coolant (about 10L)

coolant flush

sealing agent to coat the cylinder block drain plug thread (referred to as: three bond 1386B in the manual.)

car jack/ramp. I'm thinking a trolley jack, will probably come in handy time and time again. anyone know how much a good one costs?

car stands to put under the car once raised

copper washer (to replace upon refitting) for the air release plug near intake plenum. (anyone know what size??)

plus things I already have:

socket set

basic tools, eg spanners, screw drivers, pocket knives etc etc.

as i'm a bit of a novice when it comes to working on my car, i'd really appreciate any tips or advice people can offer. i plan on taking photos and making a thorough DIY for this forum.

have i left anything out that i'll need?

and a few specific questions i have already. where exactly is the jacking point for the front of the car using a trolley jack? the picture in the manual is not too clear. also where is the block drain plug for the coolant? left or right side of block? i don't wanna confuse it with say... the oil plug and drain the wrong system!

ahhh sorry for the long winded thread. thanks for any help :pwned:

Godzilla32 Veteran

Godzilla32

Posted
Posted

I'd say the Rb25 block is the same as the RB26 block so the drain plugs are on the right side of the engine (drivers side). I cant guarantee you will be able to get to them though. If not dont worry too much just make sure you back flusht he radiator and flush the whole system including the heater core. I have personally written up a few threads on good techniques of how to properly flush the cooling system so hopefully you found them.

Jack the front of the car off the cross member. Its the very solid looking black piece of steel that runs accross the beneath the engine.

Deren

ak_stylez Community Regular

ak_stylez

Posted
  • Author
Posted

Hey thanks for all the replies everyone :P

I went to supacheap and the cheapest (only) trolley jack they had was for $180. A bit more than I was expecting...

also, does anyone know what size washer is needed for the air bleed valve near the intake manifold? the manual doesn't mention a size, just that it should be replaced.

Godzilla32 Veteran

Godzilla32

Posted
Posted

Its easy to get to so just re-use the washer and if (most likely wont) it leaks then you can replace it at a later time. Im sure it would only be a couple of bucks from Nissan. Everyone makes Nissan out to be rip off merchants but i can guarantee i have bought more parts from Nissan than anyone else here in my ground up build. I have found that common things can be bought for quite cheap. Sometimes you get a nice surprise and others i'll have to admit you get a nasty shock. However in my mind unless its performance aftermarket gear, nothing beats genuine for quality.

  • 3 weeks later...
skylne77 Newbie

skylne77

Posted
Posted
hey everyone,

looked under my radiator cap about 5 months after having installed a new alloy radiator, and the coolant has turned from a nice clean green to a dirty brown. the state of the coolant was quite poor (even worse) before i replaced the radiator, and at the time we only flushed the system with water. My mechanic said the rusty water might return until i flushed it thoroughly with one of those radiator flush cleaner things from supacheap.

so, now its time to do just that. i had a look at some threads via search, and also a copy of the manual i found on the internet.

before getting started, i just wanted to make sure I had everything I needed.

here's a list of things i'll need that i compiled from both the manual and various threads:

coolant (about 10L)

coolant flush

sealing agent to coat the cylinder block drain plug thread (referred to as: three bond 1386B in the manual.)

car jack/ramp. I'm thinking a trolley jack, will probably come in handy time and time again. anyone know how much a good one costs?

car stands to put under the car once raised

copper washer (to replace upon refitting) for the air release plug near intake plenum. (anyone know what size??)

plus things I already have:

socket set

basic tools, eg spanners, screw drivers, pocket knives etc etc.

as i'm a bit of a novice when it comes to working on my car, i'd really appreciate any tips or advice people can offer. i plan on taking photos and making a thorough DIY for this forum.

have i left anything out that i'll need?

and a few specific questions i have already. where exactly is the jacking point for the front of the car using a trolley jack? the picture in the manual is not too clear. also where is the block drain plug for the coolant? left or right side of block? i don't wanna confuse it with say... the oil plug and drain the wrong system!

ahhh sorry for the long winded thread. thanks for any help ;)

you know u can take your car to a radiator specialist, and he will do all that and more and it will be cheaper than what its going to cost you, my water was rusty aswell a few years back, you have to make sure you put in enough coolant, but also not to much, and you will need to do this every 2-3 weeks, until all the rust is cleaned out,i reccomend u take the radiator out and get the hose in from the bottom, you have to make sure all the shitty rust is out, i did 4 radiator changes in a space of two months, and the last one i took it to a radiator bloke, he changed a few things, high power flush, and new coolant, never had a problem since, he charged me around $85.00

R338OY Veteran

R338OY

Posted
Posted

Good on you for giving it a go mate. You'll learn heaps.

You can jack the car up from the cross member (strongest place) directly beneath the motor, or i sometimes jack it from the towing points (big chunky oval bits sticking down on either side of the engine) when i'm in a rush.

Also don't use water to flush anything as it causes the system to rust (bet you've already read that though)

Otherwise you've covered everything. Get stuck into it, take your time, and looking forward to the tutorial ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 GTST - 600KW+ RB28/CD009 Build

      By GTSBoy · Posted

      Yucky. Things haven't gotten any better though. Now you have Emerson and Honeywell pushing these massive DCS/Scada things with proprietary hardware. They're not a PLC, they're not a computer, they're a...distibuted PLCish/DCSish monster of thing, that only they can program because they make the barriers to entry for anyone else so fricking high. And their developers are all located in the third/developing world (and India, in case anyone does not include that place in that category) and there are terrible failings of the ESl variety, of the care and common sense variety, and f**king forget about Functional Safety. Not a one of them has any idea what it means to comply with an IEC 615xx series standard.
    • niZmO_Man
      Is r33 gtr steering wheel the same as the gtst?

      By niZmO_Man · Posted

      oi (you're right though)
    • pogman
      Low oil pressure after WOT

      By pogman · Posted

      All of the ECU grounds are to the chassis, the IGN grounds are to the cylinder head and i believe all the OEM body harness are left in original locations, im trying to work out if i can tell if the sensor voltage itself is losing any power to it from the very low ECU voltage. But yeah a manual pressure gauge will help in picking which path to actually chase. Also please dont bully my wiring plan i never designed it to be universally understood hopefully it still can make sense to you, im a wiring virgin.  1 thing i have just noticed the pressure sensor in question relays both pressure and temperature, the temperature reading holds nice and steady despite the low ecu voltage but the pressure reading is the one that jumps around alot so maybe it is really a pressure issue? wiring plan.xlsx
    • Yeetus
      RB25DET Solid lifter conversion

      By Yeetus · Posted

      Gday, Due to not finding much up to date info on this topic I thought I'd make a thread to get peoples latest opinions/recommendations. Background info -  I've got a S1.5 R33 GTST as a fun project car, mainly for street use and occasional drag strip, apart from all the cosmetic things I'll be doing a full rebuild of the engine with forged internals. Since it'll be getting new cams (kelford) and springs to match I thought I might as well get new lifters and valves while I'm at it, the dash says 160k KMs but the engine seems pretty tired, compression measures about 130psi across all cylinders so I'd like to freshen everything up. This is where I'm tempted to just fork out the extra and go solid lifters while it's all apart, aiming for 400-450kw atw with a flex tune. Assuming all supporting mods (oiling, fuel and all bolt ons) with a lightly ported head and turbo to match (yet to make a decision possibly gtx3582r or similar from Hypergear) I've seen the Tomei kits with just the buckets getting around, Supertech sells most things - Supertech High Performance Cam Followers | Trusted Racing Cam Followers Questions -  Has anyone found the Hydraulic lifters to limit them at this power level? Is it usually found that you can just clean the stock lifters and find they work fine?  Does going solid lifters save any headaches/issues with hydraulic lifters in the future? Any recommendations on other things that will need to be replaced, I know I'll need to get the solid profile cams but can you use the same type of valves and springs/retainers and is it recommended to change the guides and stem seals?    Summary -  Basically looking for pros/cons and wanna know if I'll actually need the extra RPMs from solid lifters or it'll just be bragging rights to say it ReVs OvEr 8000 Cheers
    • MBS206
      R32 GTST - 600KW+ RB28/CD009 Build

      By MBS206 · Posted

      Ha ha ha, this stuff they had was installing Toshiba PLCs that were made some time in the 1990s, and they were replacing GEM80 PLCs. To let those two talk (staged upgrade along a ~1.2km long building that was split into 4 sections), was a bunch of WinXP machines running Java gateways... There was no way to put something like ProfiSafe in... Most of the HMI machines were WinXP, with Java program, with a custom button board emulating a keyboard... About the only buttons in the operator stations that went direct to the PLCs was the eStop. There was some interesting design stuff in that place...
×
×
  • Create New...