Jump to content
SAU Community

Recommended Posts

Not sure what you're trying to ask, but i'll try to answer it

The following is just MY OPINION and may be incorrect or possibly damaging :spam:

This done in what i beieve is my order of performance modification

100% std car - 7psi

Full exhaust system , quality panel filter, bleed valve - 10psi

FMIC - 10psi

aftermarket ECU - 13psi

Upgraded turbo - 18psi

rebuilt engine using quality performance parts - 20psi (pump fuel) / 35psi (race fuel)

All depends on the tunning :D

Boost DOES NOT equal power. Making the engine "breathe" easier and having less flow restrictions produces power. :thanks:

In fact boost produces heat and too much heat results in less power :spam:

Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3754271
Share on other sites

Iv heard rumours that if u slap on a TYPE R sticker on the fenders, it gives you 10psi extra boost, just like that, even on non-turbo cars.

thats a vtec sticker you idiot! typeR ones are good for another 1k added to redline

I'm assuming the thread starter is fairly new to all of this so i'll cover the basics, some of which has already been mentioned.

You can just add boost. a bleed valve or ebc will do it. It's virtually useless without freeing up the exhaust first.

In terms of the basic mods, exhaust, intake, intercooler, boost controller, management, injectors & pump, afm, turbo in that order

There is a lot of information floating around, check the sticky dyno thread up the top to give an idea of what mods do what to power.

Edited by BHDave
Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3754437
Share on other sites

thanx for your answer r33cruiser and exspecially Al.

And for you paulr33 go and die. Im not wanting to blow up my engine. And for the rest of you grow up. Why give stuipd answers when there not needed for? I asked a valid question and i got a valid response why add spam to the board and try and make yourselves feel and sound mad? Get a life.

Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3754850
Share on other sites

Maybe if you worded the question a bit better it might make more sense, however looking at the dyno thread at the top of the screen, is a great way to learn what you need to make the power you are after.

PS pauls answer was the exact correct answer to the question you asked

Edited by Adriano
Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3754895
Share on other sites

ow fully sic mate, slap a sticker on the side, grab ya self like 50PSI :) . Everyone knows a sticker dosnt add anything. SO why say stuipd shit? This is what ruiens these forums stuipd responses.

Dude, no.

What ruins forums is people who post the same old question for the 5000th time. And then get offended when it's pointed out.

ffs search you humourless nub.

Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3755414
Share on other sites

High, Just wondering what sort of mods you can do to a car, any turbo car really weather it be 180sx or a r32gtst. Just wondering what mods let you ahieve a certain amount of more boost? E.G 'blah' adds 1-2 PSI.

-->

just get a boost controller and run whatever boost you like

=

thanx for your answer r33cruiser and exspecially Al... And for you paulr33 go and die.

Ouch...

PS pauls answer was the exact correct answer to the question you asked

:laugh: Paul did technically answere the Q it seemed like u were asking ;)

Edited by GeeTR
Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3757121
Share on other sites

thanx for your answer r33cruiser and exspecially Al.

And for you paulr33 go and die. Im not wanting to blow up my engine. And for the rest of you grow up. Why give stuipd answers when there not needed for? I asked a valid question and i got a valid response why add spam to the board and try and make yourselves feel and sound mad? Get a life.

dude, chill out, paulr33 is right you know, thats what boost controllers are for. you can turnit down to 2psi if you want to. If you run 10-12psi on a normal engine/turbo, its not going to blow up.

Link to comment
https://www.sau.com.au/forums/topic/212483-high-psi/#findComment-3757147
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ...just a note of warning, you shouldn't drive it about with the TCU in limp mode with only 3rd gear available ~ apart from the fact you end up sheering the ATF at the torque converter interface, the high clutch in these isn't especially the strongest, particularly bolted to the RB25DE mill...which is likely a 4AX01 box with lighter duty high clutch (the RB25DET got the bigger high clutch)...be careful out there...
    • Hoping to do similar mods to my RB20 once I get it running and reliable again
    • As you're looking at using a Link ECU, then large injectors are not a problem. But there's not really any need to go 1000s on an RB20 unless you're planning >>600HP on E85, which would seem unlikely. There are other options for injectors. The Xspurt ones are available from a number of places and you can get them in the mid 600s and 725cc, which is probably a sensible place to be. These are all EV14 based. If you are not using the stock AFM (at all, which would be the case with a Link) then a large turbo intake pipe to suit the ATR turbos is not an obstacle, so you should use one instead of a highflow. Results will be better.
    • Hey guys,  I'm after some advice and this here is the best place to get it imo. I was a member a looong time ago under another account, with a lost email address. Its nice to jump back on and see some of the same names still giving good advice.  I mothballed my car when i moved to perth in 2013, and after getting towed across the nullabor a few times it has officially done more km's on a trailer than under its own power. Now that i have started the process of tidying up and modifying it, i see the fruit available (and the fruiterers selling the produce) is different than back in the day. hence my questions, as i used to 'know' what to get and now, i'm not so sure. Engine wise the car (92 gtst) has a walbro 255, k+n, fmic, cam gears and and turbo back 3"exhaust. Wish list is a Hypergear high flow or ATR43G1, Link G4x and some newer injectors before a tune up. My goals are modest, only low 200's power wise. i know i could achieve this with less, but i've been swapping out old for new where i can. Every cooling hose has been replaced, along with mani gaskets, WP, thermostat and radiator, fuel pump and timing belt, tensioner and idler, and i rebuilt the steering rack. Regarding the injectors, the fruiterers all seem to sell what used to be considered quite large injectors. There are a lot of options for bosch 1000cc EV14's, and i would like to know if that is a suitable choice for my build. Is modern injector design good enough to run these at the low duty cycles that i likely would be? is there a downside to running a too large injector these days? or, would there be an upside to running a smaller injector at higher duty cycle? I can see that there are smaller injectors still available, but the ones i have seen specifically marketed for RB's are pretty large (see: https://golebysparts.au/collections/fuel-rail-injector-kits/products/nissan-rb20-fuel-rail-bosch-980cc-1150cc-injectors-turbosmart-fpr800-regulator-kit), and i dont know enough about them to say one not marketed for RB's would fit or not. I have searched the forums, and amongst all the posts on older tech, I did see gtsboy recommend EV14's, but no size was mentioned... again, i'm not clear on if the smaller size bosch injectors are also EV14's as they do look similar.  also, if someone can recommend a tuner familiar with RB's in the Geelong or West Melbourne area i'd appreciate it. Thanks in advance guys. Cheers, Rowdy  
    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
×
×
  • Create New...