Jump to content
SAU Community

Recommended Posts

Give the person doing the machining the block and ask them to find out if the block will need to be bored out then get your pistons based on that. Not every brand of piston/ring combo is made for the same tolerances, too big and you get blow by and lots of piston slap issues too small and the pistons may not even move when its up to temp.

Give the person doing the machining the block and ask them to find out if the block will need to be bored out then get your pistons based on that. Not every brand of piston/ring combo is made for the same tolerances, too big and you get blow by and lots of piston slap issues too small and the pistons may not even move when its up to temp.

Whats why you bore the block to suit the pistons...

So basically, the engine builder might say "the block needs boring out 20thou (0.5mm)" so then I'd go buy some 20thou oversize pistons and the pistons would come with a spec sheet detailing the required bore clearances, which the mechanic would use to bore the block to the correct size?

  • 3 weeks later...
yeah, we dont want to re-invent the wheel here.... if only they would make a piston with a small dome.. :P problem solved

Dave, there are dome top pistons for the twin cam 30. Arias make them 9.2:1 CR, they also make another slightly higher CR piston also but cant remember what it was.

Edit. Found the info.

p/n= AP332104

10.6cc dome top

21mm pin

1.280" compression height

Only stocked in 0.20 thou oversize (86.5mm).

COMPRESSION RATIO 9.2-9.4

p/n= AP332105

13cc dome top

21mm pin

1.280" compression height

Only stocked in 0.20 thou oversize (86.5mm).

COMPRESSION RATIO 9.5-9.8

Edited by TiTAN

hey im just after a quick hand..

i have found some dirt cheap forged arias pistons with 8.5-1 comp ratio with the single cam head..

what would the comp ratio be with my rb25de head??

thinking around 7.8-1??

is their any down sides to decking the block to get higher comp ratio??

id like comp ratio of around 8.6-1..

cheers tom

  • 9 months later...
  • 1 year later...

Using either the RB25 or RB26 head on the RB30 block you need to use RB30E pistons the RB30ET pistons will result in a far too low compression ratio to be much use as a street car.

Hey guys sorry to revive an old thread. Im also building a 25/30, R33 S1 turbo head and RB30 turbo block and as TITAN said it will give me way to low compression ratio (to my liking anyway). I was looking more between 8.5-9.3 compression ratio. I dont want to spend a fortune on forged pistons (Im only looking no more than 350hp atw), so i was thinking more towards getting stock pistons. Do you guys recommend getting a RB30 NA pistons or should I go more towards RB25 NA/Turbo pistons?

Sorry for the n00b questionsclosedeyes.gif any help would be greatly appreciated

Thanks in advance.

http://cgi.ebay.com/...8#ht_1055wt_907 ermm.gif

HEHEHEHErofl.gif

  • 2 years later...

Sorry to dig up such an old thread but I searched long and hard and I can't seem to find the answer. With stock rb30e pistons and a r33 s1 rb25det head (obviously rb30 block) does anyone know how much I can deck the block before valve piston clearance etc becomes an issue? The block is stock as a rock no previous decking as far as I know

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...