Jump to content
SAU Community

Recommended Posts

hey guy's just asking the turbo guru's here if its possible to correct the massive mix match in housing/wheel design that is present in the gt2876r... the turbo is strapped to a rb25 and is rediculusly laggy for not alot of power or "punch" spec's are :

Turbine

-Wheel: 53mm w/ 62 trim

-Housing: .64 ar

Compressor

-Wheel: 76mm w/ 48 trim

-Housing: .70 ar

4inch front mouth

its for a moded std manifold...

please no suggestion's of changing turbo's etc at this time, as i would like to explore the possibility for changing housing's etc...

Link to comment
https://www.sau.com.au/forums/topic/213319-2876r-downsize/
Share on other sites

say for example, 1 bar actuator presure. 2nd and 3rd gear approx fullboost @ 4500 rpm... this is untuned though, running old tune from std turbo, however i cant see the turbo getting anywhere below what i'd be happy with...

Link to comment
https://www.sau.com.au/forums/topic/213319-2876r-downsize/#findComment-3768006
Share on other sites

Your call but your not going to fix that thing with housing alterations , the only genuine option is a larger .86 A/R turbine housing and that will only give it more turbine lag .

The problem is it has a modern low blade count light weight 54mm diameter turbine trying to drive a dinosaur 76mm T04S compressor wheel . Changing housings won't alter the fact that its compressor is a really bad match for its turbine .

Why Garrett continue to sell those POS things I'll never know .

IMO it has to go if you want you car to be lots better .

Sorry , A .

Link to comment
https://www.sau.com.au/forums/topic/213319-2876r-downsize/#findComment-3768439
Share on other sites

Are you sure about that turbine trim? It should be the same as a 2871 rear end.

The only way you could make that turbo usable is to replace the whole front end. I would suggest .5 A/R generic t04e comp cover and backing plate, with a 71mm 52 or 56 trim compressor.

By the time you get the work done and supply the parts it'd be cheaper and easier to just find a second hand replacement 2871 on NS and sell yours. They all seem to be going bigger these days for some reason, you may even find a sucker to buy yours :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/213319-2876r-downsize/#findComment-3768884
Share on other sites

By the time you get the work done and supply the parts it'd be cheaper and easier to just find a second hand replacement 2871 on NS and sell yours. They all seem to be going bigger these days for some reason, you may even find a sucker to buy yours :D

no way.......NS members are way too astute than to buy a 2876 - thats only something a skyline driver would buy :laugh:

Link to comment
https://www.sau.com.au/forums/topic/213319-2876r-downsize/#findComment-3770950
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...