Jump to content
SAU Community

Recommended Posts

guys..!

i have a manual boost controller and a GFB BOV...

and i do NOT know how to fit them, was wondering if anybody out there would want to do it for me in exchange for a couple of brewies or $$$ and if nobody can do that or can be bothered to do it tell me how much it will cost at a workshop?

also, my GT-T has a standard boost gauge, would i have to get one that runs over 1 bar to use the boost controller more efficiently and are there any problems if i use the standard one?

(reason i ask this i think stock i'm running 7psi but i wish to run at around 12psi...)

the BOV apparently has to get welded on to my engine too, it's just the trumpet thing and i don't have an aftermarket cooler SO...

any suggestions out there? for those that don't know me i'm not the most literate person mechanially

all advice will be genuinely appreciated, thank you

Andrew :D

Link to comment
https://www.sau.com.au/forums/topic/213420-bov-and-manual-boost-controller/
Share on other sites

hey mate,

I wouldn't go running your car at 12 psi without a bigger intercooler otherwise you could get engine knock which is bad also would suggest getting an aftermarket boost guage as that way you can monitor the boost better than the stock one. Running the car at about 10 psi should be fine and not cause any damage to the engine.

The bov should just bolt up where the stock one goes but not knowing too much about rb25s i wouldn't be able to tell you.

If wou need a hand with anything send me a pm and i can help you out

:D

Matt

just a precaution but if you wind up your boost you should get it on a dyno to check air/fuel ratios. so it is better to get a workshop to do the lot. i use IN TUNE PERFORMANCE. they are in the workshops list below. he charges 88/hr and about 80 bux for a check on the dyno

http://www.skylinesaustralia.com/forums/Co...hr-t191756.html

Edited by Pal

hey guys, thanks for the kind advice...

guy, everything's always easy isn't it? haha so how about that suspension?

i don't think i can live without my suspension man!

umm... matty, i'll send you a pm... i can't afford $88 an hour right now especially for a job like this so i'm sure me and you can work something out...

if anybody else out there has any nice words they'd like to say you're more than welcome to, please do so...

Andrew :D

Suggestion: Get an adaptor if you want to install the bov or use silicone pipe! Backyard welding doesnt look the best and you dont want your r34 to look like sh*t under the hood do you? Be wise and get it done properly the first time!!! Save if you have to!

what do you need done to your suspensions?

if your changing to coilovers or something like that it is really easy job, just need a socket set, a jack and about 1hr of your time (maybe less, maybe more)

but remember if you change any suspension parts you will need a wheel alignment, i changed to a different set of coilovers and ended up with some massive toe out

lol guy is the one that is after suspension...

i have mine in yet i have no f*cking clue what type os setup it is *shakes head* god i'm useless...

alright wel i'm set about getting the BOV and MBC in, i'm also thinking (and hope all you guys out there can help me with this one)...

my car is due for it's major service (100,000km's) so should i save up some $$$ and get the FMIC and get all 3 (FMIC, BOV and MBC) all in at once then tune it at the same time with my major service and has ANYONE got ANY idea as to how much this will cost and how much longer i can drive my car until i SERIOUSLY need to change the stuff for the major service...?!?!

danny at imports101 changed a lot of my stuff around before he sent the car to the pits, only things he said i needed to change was the timing belt and i think that's it, all the filters and coolers and fluids and everything were already done i think around 8,000km's ago...

never mind, any idea how much my mechanical desires will set me back?

rough estimate is okay, will go to danny i think for the major service and fitting of all that stuff

cheers,

Andrew

if someone has a reasonable offer then yeah i'm selling the car...

BUT i'll be doing things slowly if nobody buys yet ie. FMIC, BOV, MBC and also probably different kit + paint and some interior goodies etc.

you guys know how it is, for now though i've had some offers that aren't tempting enough so i might play with the car until i see a cash offer

i'll be ringing a few workshops tomorrow eh

:D

hey also andrew if you wanted to do it yourself or not have to pay a garage to do it my housemate and i would do it for a small fee (only because timing belts are time consuming to change) we live just around the corner of where you saw us the other day. Send me a PM if your interested

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't think there's any way someone is push starting this car.. I honestly can barely move it, and moving it and steering it is just flat out not possible. I'm sure it is, but needs a bigger man than me. I have a refurbished starter now. The starter man was quite clear and consise showing me how nothing inside a starter really should contribute to slow cranking, and turned out that for the most part... my starter was entirely fine. Still, some of the wear items were replaced and luckily it didn't show any signs of getting too hot, being unfit for use, etc. Which is 'good'. I also noticed the starter definitely sounded different, which is a bit odd considering nothing should have really changed there.... Removed and refit, and we'll pretend one of the manifold bolts didn't fully tighten up and is only "pretty" tight. GM only wants 18ft/lb anyway. I also found a way to properly get my analog wideband reading very slightly leaner than the serial wideband. There's Greg related reasons for this. The serial output is the absolute source of truth, but it is a total asshole to actually stay connected and needs a laptop. The analog input does not, and works with standalone datalogging. Previously the analog input read slightly richer, but if I am aiming at 12.7 I do not want one of the widebands to be saying 12.7 when the source of truth is 13.0. Now the source of truth will be 12.65 and the Analog Wideband will read 12.7. So when I tune to 12.7 it'll be ever so slightly safer. While messing with all of this and idling extensively I can confirm my car seems to restart better while hot now. I did add an old Skyline battery cable between the head and the body though, though now I really realise I should have chosen the frame. Maybe that's a future job. The internet would have you believe that this is caused by bad grounds. In finding out where my grounds actually were I found out the engine bay battery post actually goes to the engine, as well as a seperate one (from the post) to the body of the car. So now there's a third one making the Grounding Triangle which is now a thing. I also from extensive idling have this graph. Temperature (°C) Voltage (V) 85 1.59 80 1.74 75 1.94 70 2.1 65 2.33 60 2.56 55 2.78 50 2.98 45 3.23 40 3.51 35 3.75 30 4.00   Plotted it looks like this. Which is actually... pretty linear? I have not actually put the formula into HPTuners. I will have to re-engage brain and/or re-engage the people who wanted more data to magically do it for me. Tune should be good for the 30th!
    • There are guys on Facebook under, Infiniti Owners Australia   https://www.facebook.com/share/g/1Z3RbPqx4k/?mibextid=wwXIfr What Whp are you after and I can help, and join this Q group in the states. https://www.facebook.com/share/g/19A59cN3JR/?mibextid=wwXIfr
    • Does any of you guys have instagram pages for your builds? Keen to see some Aussie builds. I still can't figure out how to post photos in here.
    • That awesome thanks for that. 
    • You can Remote any of these VR30..globally  Check: AMS Performance | Racebox | Sonic Tune | Soho | Z Motorsports | Specialty Z    Performance Parts | AMS | Z Motorsports | Boosted 6 |    Exhaust | Fast Intentions | ARK | MBRP Motordyne | Borla    There is someone in Sydney with 650whp   I am at 430whp without flex fuel, but FBO & Flex-fuel will push you to 500whp!!  
×
×
  • Create New...