Jump to content
SAU Community

Recommended Posts

Hi all,

been a while since I have posted here. It's good to see the community is still strong. New GT-R looks good too.

This is an update for the topic of R32 GT-R's running badly when they are cold. Most posts involved complaints of the car surging and a coughing sound coming from the engine bay, with decreased performance, then at a certain point everything would go normal like a switch had been thrown.

After a bit of testing using my Power FC, I think I have come up with an answer.

I noticed that when I installed the power fc that the problem went away. It makes me think that the problem lies in the standard ECU, sorry guys, bad news for some because there is probably nothing you can do about it. It has the very similar aspects that bad IGNITION TIMING has, as in, the ignition timing when it is cold is retard up to shit.

This explains the lack of power and the coughing(sort of acting like antilag on rally cars, where the turbos is spooling really low in the rev range). What is happening is the ECU is retarding the timing when it is cold, then when it hits a pre-programmed temperature it changes it to normal. Power FC's are programmed differently and that's why it goes away, although if you played around with the warm up setting you could get it to do the same thing. I think it is coolant temperature correction....

If anyone thinks they can expand on this, feel free to add to this topic.

Link to comment
https://www.sau.com.au/forums/topic/213464-r32-cold-running-update/
Share on other sites

Interesting topic to come up. I have an r33 with an rb20 remap in mine and am having a very similiar issue. Cold start the exhaust note "sounds" different and as you take off the turbo spools very loud, no power and all of suddden like a light switch it takes off. I have seen the issue with consult plugged into the laptop and the timing sits dead flat on 7 degrees btdc, then like a light switch at about 2200rpm, hits 30-40 degrees btdc and off it goes. If I shut the car down and restart it, 85% of the time the car will then drive normally.

I know for a fact with my car that the knock sensors are faulty and am yet to bypass them in the next week to see if the problem goes away. Keep in mind mind the Power FC will not adjust the map accordingly if it senses knock, all it does it display the level of knock, unlike the standard ecu which will pull timing and add fuel as far as I gather. It's possible that the motor is a little noisy on startup and dropping the ecu into the knock map. Rather weird issue and I am clutching at straws but bypassing the knock sensors will definately tell me if that is causing the issue.

I have seen my ecu produce 2 faults, one was knock sensors, the other was ignition signal. CAS possibly playing up....maybe, although i tend to think not. I need to look into the ignition signal fault and see what variables the ecu looks for to see why this would be produced. My alternator is also a little suspect.

Maybe grab consult, a laptop and cable and whack it on your car before a cold start and see what fault codes come up?

Probably due to Power FC being properly tuned for the car, therefore when its running rich while warming up(cold start), its better suited to the modifications of the car.

Might find guys running remaps/NIStune etc. don't have these issues (if tuned properly).

I don't think this is a inherent flaw with the stock ecu, but more a symptom of Nissan's 'safe' factory tune.

My gtr doesnt do any funny stuff at all when its cold... ever

its never done anything funny at any stage... ever :banana:

its gotta be something else, not ecu related

possible its a sensor malfunction that the fc doesnt rely on heavily.. like the knock. factory ecus run the cars off the knock whether the fc doesnt. atleast from what ive read. theyre like a switch.. either its knocking or its not knockin enough for it show up *shrugs*

Edited by Bumblebee

It's just cold start, I don't see what the big deal is. I've seen it mentioned many many times before, you shouldn't be driving your car hard until it's warm anyway so just deal.

My car has always done it, stock RB20/ecu and now with RB30/remapped ecu, until coolant is up to temp it's in "cold start" and drives like a pig with more than say 5% throttle, so I just don't rev it over 2000rpm or use much throttle until it comes out of cold start.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks, I removed the fuse and the relay from the car and made my own circuit with them to test them with a test bulb.  I will look for the wiring diagram and go from there.
    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
×
×
  • Create New...