Jump to content
SAU Community

wiring in front seats

JT

By JT,
in Exterior & Interior Styling

 Share

Recommended Posts

JT Community Regular

JT

Posted
Posted

Hi all,

I need some questions answered.

My R33 series 1 has a wire come from the flooring and plugs into the bottom of my drivers and passenger side seats. Then another wire comes from there and hangs loosely with nothing connected. What is this for? Airbag? Should the wire just being sitting there loosely?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/21354-wiring-in-front-seats/
Share on other sites
JT Community Regular

JT

Posted
  • Author
Posted

Thanks,

But I found the problem is that when they removed the original seat belts, the wires were connected to where the belt connects. This would send a signal to the dash saying your seat belt is on or off. Just a safety feature.

So the new povo belts they put in would not have this feature and so the wires cannot be connected.

skysaresilver Community Regular

skysaresilver

Posted
Posted

hey guys,

just a quick answer to shed some light on whether they can be used for anything else.... i wanted to hook some under seat neons up to them which would have been controlled by a switch on the dash, but before buying the neons i tested the currency of the plugs with a multimeter and found that there was less then 0.20volts going through, therefore there was not even 1volt going through, so i gave upon the idea of using them for neons..... i'm not saying i'm right, as it could just be my car, so can anyone else here test them as well to see whether u get the same results, as i really wanted to use them for some neons, perfect spot and all :P,

many thanks (interested to hear results now!!!!)

williamc Collaborator

williamc

Posted
Posted

yeah, as stated above, I was told in my R32, that they are for the seat belt light. The chairs sense if someone is sitting in them ,and if the belt isnt on, the light on dash will flash.

For compliance the seatbelts are swapped as the jap ones dont have ADR approval. The seatbelt, and the seat belt thingy that it plugs into are swapped. Mybelts even have a different anchor bolt into the chassis near the door....

As this is only a small function, it wouldnt require much voltage.

Will

  • 5 weeks later...
Craved Grand Master

Craved

Posted
Posted

Do all Skylines have air bags?

My series 1 GTST doesn't have an air bag at all (dash or wheel) and it has those wires under the seats!!! maybe rule thos options out!!

Has anyone looked at there new seat belts for front seats!! had my interior removed recentl;y and those seat belt moun ts done look very safe!!!

it's like a single bolt through thin body steel, going to a metal plate that the belt bolts onto!! any one else seen this!!!???

Bozz Proficient

Bozz

Posted
Posted

The wires are there in the R32's for the electric seat belt retainers - you may notice sometimes that the seat belt will not automatically retract or have any force on it wanting it to retract. As soon as you undo the belt from the buckle, it automatically retracts. This was as a comfort feature, I thought it was rather stupid personally and disconnected it, thus always having tension from the belt on my chest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      I just got to work and skimmed through 61508 and 61511. I was surprised the CSA adopted both, but neither are enforced. To recap what I read, it states that in a perfect world, they should be segregated but they acknowledge that this is not industry standard and clearly mention that they allow mixing of safety and non-safety. 61511 also mentions software segregation like AB does in their safety PLC's.   Now if only I could go back to control, let alone safety over comms. In my current line of work, we're only allowed monitoring and basic control over comms. Everything critical must still be hard wired as much as possible. 
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      I've unfortunately never been as they're on the complete other side of the continent and another country that isn't currently letting us in as easily as they use to. I even heard their stop signs over there actually say "Stop" instead of "Arret". If I decided to trek the 48h drive, I wouldn't know when or where to stop haha. Whenever I order parts from UP Garage, I order from Japan as it's cheaper. Same with GKTech... oddly enough, it's cheaper shipped from Australia then it is the US.  UP Garage Japan operates their US leg though, unlike Tomei. If Tomei JPN had the power to close down Tomei USA, I'm sure it would be done in a day. They're two completely separate entities. Tomei JPN messed up somewhere originally agreeing to its creation and got sacked big time. 
    • KKaplumbaa
      SR20 to cefiro

      By KKaplumbaa · Posted

      I asked someone about this and he told me about the Audi 1.8T engine. But I think it would be difficult to swap
    • MBS206
      The Cool Tools Thread

      By MBS206 · Posted

      I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • KKaplumbaa
      SR20 to cefiro

      By KKaplumbaa · Posted

      SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
×
×
  • Create New...